background image

20

IoT Interworking

Make Your Life Smart

Security Code

Chapter 3 Broadcast Compliance

Instructions

LSD4WN-2332XGW1 supports AS923, AU915, KR923 and other frequency bands. The maximum

output power of the gateway is 23dB±1dB. The transmission power is adjustable. Please follow the local

radio management regulations to limit the working power of the gateway.

Chapter 4 Precautions

1. It is strictly forbidden to power on the unconnected antenna. It is strictly forbidden to replace

and remove the antenna with power;

2. Before connecting the power, you must ensure that the connections are good;

3. The Ethernet connected to the gateway needs to obtain the IP automatically and can access the

public network.

4. The user should not replace the power adapter at will;

5. For outdoor installation, please take lightning and rain protection measures;

Chapter 5 Troubleshooting

1. The node is unable to communicate with the gateway normally:

Solution:

Check if the power supply and network are normal;

Whether the connected network cable can automatically obtain IP, and does

not bind the MAC address;

Confirm that the node gateway works in the corresponding frequency table;

Confirm that the server is normal;

Confirm that the gateway has added a server and the parameters are the same

as the server;

Summary of Contents for LSD4WN-2332XGW1





















Reviews: