2 | EN
Copyright © Liberty Pumps, Inc. 2021 All rights reserved.
2138000G
Contents
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 | EN
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 | EN
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 | EN
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 | EN
Safety Guidelines
Safety Precautions
Always disconnect power before installing or servicing this
product. Qualified personnel must install and service this
product according to applicable electrical and plumbing
codes.
Always wear dielectric rubber boots and other applicable
Personal Protective Equipment (PPE) when water is on the
floor and an energized pump or alarm system must be
serviced as submerged electrical connections can energize
the water. Do not enter the water if the water level is higher
than the PPE protection or if the PPE is not watertight.
Do not install this alarm system outdoors. The system is rated
for indoor use only.
All electrical and safety practices shall be in accordance with
the National Electrical Code
®
, the Occupational Safety and
Health Administration, or applicable local codes and
ordinances.
Do not use this product with or near flammable or explosive
fluids such as gasoline, fuel oil, kerosene, etc.
This product is not to be installed in locations classified as
hazardous in accordance with the National Electric Code
®
,
ANSI/NFPA 70.
Alarm float adapters cannot be used with puck sensors.
Do not cut the connector off a puck sensor and wire it to the
float adapter. The sensor uses three wires for communication
and the float adapter only has two terminal blocks.
General Information
Before use, please read the following instructions carefully. Each
Liberty Pumps alarm system is tested individually in the factory to
ensure proper performance and operation. Closely following these
instructions will eliminate potential operating problems, providing
years of trouble-free service.
This high water level alarm system is designed for applications
such as monitoring sump pump basins, sewage pump basins, and
water powered back-up pumps. The alarm system comes standard
with a 9V battery backup to enable continuous water level
monitoring, even when the power is out. A built-in battery
monitor alerts the user when the 9V battery needs to be replaced.
Replace product immediately if sensor or power cable becomes
damaged or severed.
NightEye® enabled devices come equipped with wireless internet
connectivity. These devices can connect to your wireless network,
by means of an Android® or iOS® device, and send notifications
about your system in real time. This system provides peace of
mind about the status of your pump system even when you are
not home.
All of the alarms come standard with Liberty Pumps 360° red
alarm beacon powered by super-bright LEDs. In combination with
the 86 dB (at 10 ft/3 m) alarm siren, the alarm is sure to alert
occupants of any high-water condition.
Each device is specifically designed for use in an indoor residential
wastewater application. The system comes with liquid level sensor
that conforms to the needs of the intended application. The
sensor types are as follows:
•
Snap-on enclosed float for Sump Pump Applications
:
ALM-P1, ALM-P1-EYE, SJ10A, SJ10A-EYE
•
Tethered float for Sewage Pump Applications
:
ALM-2, ALM-2-1, ALM-2-EYE, ALM-2-1-EYE
•
Water puck for Puddle Sensing
:
ALM-PK, ALM-PK-EYE
To install up to three sensors, use Liberty Pumps alarm connector
splitter (sold separately, kit #K001633). A maximum of 2 pucks can
be used on a single alarm. Acceptable configurations: 3 floats; 2
floats and 1 puck; or 1 float and 2 pucks.
This safety alert symbol is used in the manual
and on the pump to alert of potential risk for
serious injury or death.
This safety alert symbol identifies risk of
electric shock. It is accompanied with an
instruction intended to minimize potential
risk of electric shock.
This safety alert symbol identifies risk of fire.
It is accompanied with an instruction
intended to minimize potential risk of fire.
This safety alert symbol identifies risk of
serious injury or death. It is accompanied
with an instruction intended to minimize
potential risk of injury or death.
Warns of hazards which if not avoided will
result in serious injury or death.
Warns of hazards which if not avoided could
result in serious injury or death.
Warns of hazards which if not avoided could
result in minor or moderate injury.
Signals an important instruction related to
the pump. Failure to follow these instructions
could result in pump failure or property
damage.
Read every supplied manual before using
pump system. Follow all the safety instructions
in manual(s) and on the pump. Failure to do
so could result in serious injury or death.
RISK OF ELECTRIC SHOCK
RISK OF FIRE
