background image

Thank you for your purchase of the Liberator Rocket Heater. This owners manual will

assist you in the proper use, maintenance, installation, and safety precautions to undertake in
the heaters operation and installation.

3  WARNING! READ ALL INSTRUCTIONS CAREFULLY BEFORE

 

 

USING OR INSTALLING! SAFETY PRECAUTIONS!

-Do   not   touch   the   appliance   while   it   is   hot,   in   operation   or   thereafter.   Educate   all

children of the danger of high temperature appliances and maintain supervision of children at
all times when children are in the same room as the appliance.

-This appliance is only suitable for burning coal, charcoal, fuel pellets, natural wood, to

include  cordwood,   twigs,   branches,   and  staves  only.   Only  with  the  Pellet  Hopper  Adapter
properly installed can the heater burn fuel pellets. Never use flammable liquids, artificial logs
containing any petroleum derived products of any kind, or any other fuels not covered in this
manual at any time under any circumstances. Plastics, foam material, or any other material not
mentioned are never to be used in any way as a fuel or for other purposes with this appliance.

-Never   use   gasoline,   gasoline-type   lantern   fuel,   kerosene,   charcoal   lighter   fluid   or

similar liquids to start or 'freshen up' a fire in this heater. Keep all such liquids well away from
the heater while it is in use.

-The ash cleanout door must never be opened while in operation.

-Do not install in a sleeping room.

-Ashes must be disposed of only when completely cooled with absolutely no embers,

cinders, or other signs of combustion in a metal airtight container and the closed container of
ashes should be placed on a non combustible floor or on the ground well away from any
combustible materials pending final disposal. If the ashes are to be disposed of by burial in soil
or otherwise locally dispersed, they should be retained in the closed container until all cinders
have thoroughly cooled.

Page 3

Summary of Contents for RMH-2





















Reviews: