background image

14

7-4.ERROR DISPLAY.

If you press the  Start/Pause button any error except 

will disappear and the machine will change

into pause status.

In case of 

if the error is not resolved within 20 sec. In case of other errors, if the

error is not resolved within 4 min. Power will be turned off automatically and the error only will be
blinked. But in the case of 

, power will not be turned off.

ERROR SYMPTOM

1

WATER INLET

Water has not reached to the pre-set level within 4 min. since

ERROR

inlet valve operated, or water has not reached to the normal

level within 25 min.

2

IMBALANCE

The appliance is tilted. 

ERROR

Laundry is gathered to one side.

Non distributable things are put into the drum.

3

DRAIN ERROR

Water has not drained enough within 5 min.

4

OVERFLOW

Water is automatically being pumped out because too much

ERROR

water is in the tub.

5

SENSOR PRESSURE

The sensor pressure switch is out of order.

S/W ERROR

6

DOOR OPEN

The 

Start/Pause

button is pressed with the door open.

ERROR

The door switch is out of order.

7

HEATING

ERROR

The thermistor is out of order.

8

SENSOR

The connector (5-pin, male, white) in the wire harness is not 

ERROR

connected to the connector (5-pin, female) of hall sensor in 

the MOTOR.

Reconnect or repair the contact in the connector.

Summary of Contents for WD(M)-10230(5)FB




































Reviews: