manualshive.com logo in svg

LG WD-1015(0~9)N(U)P, Service Manual

Share
Download
LG WD-1015(0~9)N(U)P Service Manual Download Page 10

TEST OPERATION

9

• Connect the power plug to

• In case of cotton program.      

the outlet.

• Connect the inlet hose.   

Preparation for 

Press the power button.

Press the START / PAUSE

washing.

button.

• Press both 

Pre Wash 

and 

Time

Delay

button simultaneously the

present temperature will be displayed.

• Check if the drum rotates clockwise

and counterclockwise.

• Check if water is supplied through the

detergent dispenser.

• Power off and  then power on.
• Check if the door can be 

opened after 

Door Lock

lamp

turns off.

• Power off and then power on.

Turn on Spin lamps after
pressing the Start / Pause button
and Start the machine again.

• Check drain and spin.

• If SVC is needed during 

check, remove

the remaining water by pulling 

out the hose cap.

Check the water heating.

Check automatic reverse

Check the water supply.

turn.

Check drain and spin 

Power off and open the 

Water removal 

door

Summary of Contents for WD-1015(0~9)N(U)P



































Reviews:

No comments

Brands by name

Popular brands

Load more brands