background image

SAFETY PRECAUTIONS

BEFORE OPERATING THIS VACUUM CLEANER, READ THIS SERVICE MANUAL THOROUGHLY,
AND OBSERVE EACH POINT CAREFULLY.

1. Motor filter(Air Cleaner)

1) This filter is reusable.
2) Never use the vacuum cleaner without filter.

It may damage the motor.

3) If the suction power is decreased after cleaning

dust tank, clean or wash the motor filter and air
filter.

4) The motor filter and air filters clean or wash at

least once a month

NOTE : 

Reusing of the motor filter.

• Never wash the filter in a washing machine or in a

dishwasher.

• Never use hot water for washing the filter.
• Reuse the filter after drying it completely in the

shade for a day.

• Do not dry near fire or direct sunray.

2. Exhaust filter (Micro filter)

1) This filter is reusable filter.
2) For cleaner air, filter must be assembled.

NOTE :

Reusing of the exhaust filter.

• Never wash the filter in a washing machine or in a

dishwasher.

• Never use hot water for washing the filter.
• Re-use the filter after drying it completely in the

shade.

• Do not dry near fire or direct sun ray.

Option (Choose according to buyer’s request)

Exhaust filter (HEPA filter)

1) This filter is reusable HEPA filter.
2) For clean air, filter must be assembled.
3) Dust off filter. (Do not wash filter with water.)
4) Clean the exhaust filter once 1 year.

NOTE : 

Reusing of the exhaust filter.

Do not wash filter with water.
Do not brush the filter. This will cause permanently
damage allowing dust to by-pass the filter.

3. Avoid suction such materials as :

1) Liquid or wet dust :

Clogs the ventilation holes, reduces the suction
power significantly and harms the motor.

2) Inflammable liquids such as benzene, alcohol or

solvents.

3) Burning objects such as cigarette butts.
4) Bulky objects such as vinyl, paper etc.
5) Sharp objects such as needles, pins, metal, glass

particles etc.

4. Attachments

Nozzle : for cleaning wooden floor, the room floor
and carpet.
Crevice Tool : for cleaning any crevice, inside
corners or window frames. However, do not use
the crevice tool more than 20 minutes because it
may cause harm to the motor.
Dusting brush : for cleaning clothes curtains.
Upholstery nozzle : Clean the furniture, mattresses etc.

5. Close supervision is necessary when this

vacuum cleaner is used by or near children.
Childrenís carelessness may cause damage to
the cleaner or injure persons.

6. Air exhausted from the vacuum cleaner is

normally warm. But if extraordinarily hot air is
exhausted, check if the telescopic tube, hose or
clean filter is clogged or not.

7. Electric shock could occur if used outdoors or

on wet surfaces.

CAUTIONS

BEFORE ATTEMPTING TO SERVICE OR ADJUST ANY PART OF THE VACUUM CLEANER,
DISCONNECT THE ELECTRICAL POWER SUPPLY CORD FROM THE WALL OUTLET.

1. Motor exchange

1) Separate the Body Cover and Body Base by

unfastening the screws.

2) After disconnecting the lead wires, replace the old

motor with a new one.

2. In case of exchanging other parts.

refer to the exploded view.

- 3 -

Summary of Contents for VC53 Series






















Reviews: