LG V24LH Installation Manual Download

Page: 29 / 31

ENGLISH

Installation Manual

Test running

Test running

Thermometer

1) Connection of power supply

1. Connect the power supply cord to the

independent power supply.

• Circuit breaker is required.

2. Prepare the remote control.

• Insert two batteries provided.

Remove the battery cover from the remote
controller.

• Slide the cover according to the arrow direction.

Insert the two batteries.
(Two "R03" or "AAA" dry-cell batteries or
equivalent.)

• Be sure that the (+) and (-) directions are correct.
• Be sure that both batteries are new.

Re-attach the cover.

• Slide it back into position.

3. Operate the unit for fifteen minutes or

more.

2) Evaluation of the performance

1. Measure the temperature of the intake

and discharge air.

2. Ensure the difference between the

intake temperature and the discharge
one is more than 8°C (Cooling) or
reversely (Heating).

Summary of Contents for V24LH
































Search results

Summary of Contents for V24LH

Reviews:

Related manuals for V24LH

Brands by name

Popular brands

LG V24LH, Installation Manual

Search results

Summary of Contents for V24LH

Reviews:

Related manuals for V24LH

Brands by name

Popular brands