LG V-net ACS PWFMDB000 Installation & User Manual Download | Manualshive

Page: 9 / 48

background image

9

INSTALLING THE INTERNET

B

RIDGE

Selecting the installation place

• When it is installed with wireless communication

Internet bridge shall be installed within 10m from AP.
Communication is possible up to obstacles made of concrete wall (thickness 10cm or less) or
wooden door (or window).

• When it is installed as wired cables

Connect wired LAN cable of 10m or less to the internet bridge.
Protect the exposed wired LAN cable with cable pipe.

• Power connection

Internet bridge shall be installed within 2m from the power socket.
Arrange and connect the power cable.

• RS485 cable

It shall be installed at a place where it is connected to RS485 connecting to the outdoor unit.

• Indoor installation

Internet bridge shall be installed indoor, not outdoor.
Do not install at a place exposed to rain or with a lot of moisture.
Do not store or use flammable gas or inflammables near the product.

«
...
7
8
9
10
11
...
»

Summary of Contents for V-net ACS PWFMDB000

















































Reviews:

No comments

Related manuals for V-net ACS PWFMDB000

Brand: 3Com Pages: 20

Brand: IBM Pages: 86

BB-HGW700A - Network Camera Router

Brand: Panasonic Pages: 10

Brand: Keithley Pages: 59

Brand: Oracle Pages: 112

Brand: NETGEAR Pages: 14

SuperServer 5019S-L

Brand: Supermicro Pages: 61

Brand: Time domain Pages: 64

Brand: Gate Pages: 8

Fieldpoint cFP-RTD-124

Brand: National Instruments Pages: 15

Brand: Paradyne Pages: 23

Vigor 2760 Series

Brand: Draytek Pages: 54

Brand: QuickLink Pages: 8

JetNet 3508-LVDC

Brand: Korenix Pages: 16

Turbo NAS TVS-71 Series

Brand: QNAP Pages: 51

Brand: Longshine Pages: 35

DiamondLink 3201

Brand: Patton Pages: 12

Ezi-SERVOII EtherCAT TO

Brand: Fastech Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands