LG PCS150R Pro:Centric Installation & Setup Manual Download Page 7

10

206-4191

System Setup

Combiner

RF

Coaxial 

Cable

RF 

Cable

ASI Out

PCS150R

IF Out

QAM 

Modulator

ASI In

IF In

RF Out

DTV

Upconverter

Network

Room

Receiver

Room

Receiver

Room

Receiver

RF 

Distribution 

System

ASI

Coaxial 

Cable

Laptop

PC

RS-232 Port

Connection 

RF 

Cable

RF Out

PCS150R

RF 

Distribution 

System

Network

Room

Receiver

Room

Receiver

Room

Receiver

Laptop

PC

RS-232 Port

Connection 

Combiner

Refer to the following diagrams, and complete the system installation as described on 
pages 11 and 12.  

Typical Setup Flow Charts for the PCS150R

ASI Output

RF Output

206-4191

7

Setup Checklist

Check the items listed below before you begin the PCS150R installation and setup 
procedures.

ASI Output (Optional)

__  If the system is using ASI ouput, install the modulator and upconverter that will 

receive the ASI output signal from the PCS150R. Refer to the manufacturer’s 
documentation. 

PCS150R

__   Unpack the PCS150R Pro:Centric server unit and all accessories. 

Accessories provided: Power Cord and Adapter

__  Select the location for mounting the PCS150R. Ensure that adequate ventilation is 

available.

__  Obtain the necessary attachment hardware to mount the PCS150R chassis in its 

targeted location.

__  Plan and install the necessary cabling and network (Ethernet) and AC power access 

for the PCS150R. You will also need the following to connect a PC directly to the 
PCS150R for system setup verification purposes:

•  DB9 Male-to-DB9 Female RS-232 straight-through serial cable (Example: Cables 

Unlimited PCM-2100-06 serial cable).

•  (Optional) USB 2.0-to-serial DB9 adapter (Example: Cables Unlimited USB-2920 

adapter). If there is no serial port on the PC, use the adapter to connect the serial 
cable to the PC.

__  Carefully follow the installation procedure for the PCS150R (see page 9).

__  Complete the system setup for the PCS150R (see pages 10 to 12).

Refer to the 

PCS150R

 

Pro:Centric™ Server Installation & Setup Guide

 for further 

installation and confi guration information. 

Product documentation is available online at: 

www.LGsolutions.com/products

. From 

the Products page, select 

TVs, Systems & Solutions

,

 

then 

Head End Systems

, then 

Pro:Centric Server 

(click 

Show [+] 

to view the list of products), then 

PCS150R

. Click 

the 

Literature & Downloads 

tab at the bottom of the PCS150R page, and select the 

required document(s) from the Downloads list. 

Summary of Contents for PCS150R Pro:Centric









Reviews: