LG PCS150R Pro:Centric Installation & Setup Manual Download Page 2

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR 
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE 
PERSONNEL. 

 

 

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert 
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure 
that may be of sufficient magnitude to constitute a risk of electric shock to persons.

 

 

The exclamation point within an equilateral triangle is intended to alert the user to the 
presence of important operating and maintenance (servicing) instructions in the literature 
accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO 
RAIN OR MOISTURE. 

 

Apparatus shall not be exposed to dripping or splashing and no objects filled with 
liquids, such as vases, shall be placed on the apparatus.

L’appareil ne doit pas être exposé à des égouttements d’eau ou des éclaboussures et de 
plus qu’aucun objet rempli de liquide tel que des vases ne doit être placé sur l’appareil.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class A 
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference when the equipment is 
operated in a commercial environment. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio communications. Operation of this 
equipment in a residential area is likely to cause harmful interference in which case the 
user should be required to correct the interference at his own expense.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG 
Electronics U.S.A., Inc. Unauthorized modification could void the user’s authority to 
operate this product.

COMPLIANCE: 

The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc.

 

2000 Millbrook Drive, Lincolnshire, IL 60069, USA • Phone: 1-847-941-8000

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.

2000 Millbrook Drive, Lincolnshire, IL 60069

WARNING

RISK OF ELECTRIC SHOCK

        DO NOT OPEN

© Copyright 2011, LG Electronics U.S.A., Inc.

2

206-4191

For Customer Support/Service, please call:   

1-888-865-3026

www.LGsolutions.com

206-4191

15

Notes

Summary of Contents for PCS150R Pro:Centric









Reviews: