LG MULTI F LAN090HSV4 Installation Manual Download Page 49

Page: 49 / 56

Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

MAX

MULTI

Troubleshooting Using Error Codes

Refer to Table 27 for information on the error codes that are gener-

ated from the indoor and outdoor units. These codes are the most

common that will manifest through these units. Your particular model

duct free system might generate additional codes not listed here.

Please contact LG Support if you see these types of errors and a

simple power down and boot up has not corrected the issue. You

should not attempt to fix the system yourself.

Error Codes

•

Refer to the figures below for your particular indoor unit’s LED

configuration.

• Indicate different types of unit failures, assists in self-diagnosis

and to track the frequency of occurrence.

• Error codes are shown on the LEDs of indoor units, wired

remote controller, the Single Zone unit control board, and LG

Monitoring View (LGMV) Diagnostic Software.

• If two or more errors occur simultaneously, the lower error code

number is displayed first.

• After error is resolved, the error code does not display.

Error Codes

Decoding the Error Display

The first and second number on the LED indicates error number.

Example: 21 = LED1 (Green light) 2x blink, LED2 (Red light) 1x blink

Error Code Nomenclature Definitions

• MICOM: Non-volatile memory chip where unit setup information

is stored.

•

EPROM: Non-volatile memory chip where device identification,

size, and factory defined default component operating param

eters are stored.

LED 1

(UNITS PLACE)

LED 2

(TENS PLACE)

Receiver

Figure 70: Example of IDU LEDs

Error

Code

Description

No. of Times Indoor Unit

LEDs Blink

LED1

(Plasma LED)

LED2

(Power LED)

Indoor unit room temperature sensor error

Indoor unit inlet pipe sensor error

Float switch error (optional)

Communication error between indoor unit and outdoor units

Indoor unit outlet pipe sensor error

Indoor unit EPROM error

Indoor unit BLDC motor fan lock

Indoor unit middle pipe sensor error

Table 27: Multi Zone Wall-Mounted Indoor Unit Error Codes

TROUBLESHOOTING

Summary of Contents for MULTI F LAN090HSV4

























































Search results

Summary of Contents for MULTI F LAN090HSV4

Reviews:

Related manuals for MULTI F LAN090HSV4

Brands by name

Popular brands

LG MULTI F LAN090HSV4, Installation Manual

Search results

Summary of Contents for MULTI F LAN090HSV4

Reviews:

Related manuals for MULTI F LAN090HSV4

Brands by name

Popular brands