LG MS-1905C Service Manual Download Page 13 | Manualshive

Page: 13 / 30

background image

H. LATCH BOARD ASSEMBLY AND

SUCTION GUIDE ASSEMBLY

NOTE: Suction Guide Main ASS’Y consists of Latch
Board ASS’Y and Suction Guide ASS’Y. To repair any of
them, should be removed first Suction Guide Main
ASS’Y.

1) Remove the screw.

2) Disconnect the leadwire.

5-6

Rotate right
and pull out

Latch board ASS'Y

Connecting screw

I. FAN MOTOR ASSEMBLY REMOVAL

NOTE: Suction Guide Main ASS’Y consists of Latch
Board ASS’Y and Suction Guide ASS’Y. To repair any of
them, should be removed first Suction Guide Main
ASS’Y.

1) Disconnect the leadwire from fan motor.
2) Remove the fan.
3) Remove the two screws holding the fan motor

assembly to the suction guide ass’y.

Fan Motor ASS'Y

Suction
Guide

J. HIGH VOLTAGE TRANSFORMER

REMOVAL

1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from magnetron, high voltage

transformer, and capacitor.

3) Remove the screw holding the high voltage

transformer to the baseplate.

Pull out suction guide Main ASS’Y

Remove the screw

«
...
11
12
13
14
15
...
»

Summary of Contents for MS-1905C































Reviews:

No comments

Related manuals for MS-1905C

Brand: T-Fal Pages: 48

Brand: Gaggenau Pages: 28

IDF 9011 PRO BK

Brand: Cata & Can Roca Pages: 31

Brand: Rasonic Pages: 23

Brand: Junker Pages: 84

Brand: Ultra Max Pages: 39

Brand: Vanguard Pages: 38

Brand: Prestige Pages: 24

Brand: Magic Chef Pages: 12

Brand: Daewoo Pages: 36

Brand: SEVERIN Pages: 1

Brand: Daewoo Pages: 27

Couture C9OAAAS4R0W3

Brand: Cafe Pages: 68

Combair BC-SL 728

Brand: V-ZUG Pages: 80

Brand: edenox Pages: 40

Brand: Sandstrom Pages: 204

Brand: Goddess Pages: 40

Brand: The Stone Bake Oven Company Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands