LG MB-4322AH Page 24 Service Manual Download | Manualshive

Page: 24 / 40

background image

5-14

(TROUBLE 3) Output power is low.

CONDITION

CHECK

RESULT

CAUSE

REMEDY

Output is low

Lower than 207V.

Normal

Less than 8.5

o

C.

Measure the
magnetron’s
output(See test
procedure).

Faulty magnetron.

Replace.

Decrease in power
source voltage
with load.

Suggest customer
contact local
electric power
utility co. or
qualified
electrician.

Check the
power source
voltage
oscillating.

No continuity.

No continuity.

replace.

Malfunction of the
timer switch.

Faulty thermostat.

replace.

Check the
continuity of the
timer switch
contacts.

Check the
continuity of the
thermostat.

CONDITION

CHECK

RESULT

CAUSE

REMEDY

(TROUBLE 4) Grill.

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1. Heater is not

operating.

Abnormal.

Normal.

Normal.

Heater.

Thermostat
(Grill)

Abnormal.

Malfunction the
thermostat.

Malfunction the
heater.

Replace.

Wire connection.

No continuity.

Open or loosen.

Replace.

Replace.

«
...
22
23
24
25
26
...
»

Summary of Contents for MB-4322AH









































Reviews:

No comments

Related manuals for MB-4322AH

Brand: Daewoo Pages: 17

Brand: Oster Pages: 38

Brand: Premium Appliance Brands Pages: 10

Brand: Blanco Pages: 24

Spacemaker JNM1541DN

Brand: GE Pages: 3

Brand: Dacor Pages: 12

Brand: shelolab Pages: 21

Brand: Tasty Trotter Pages: 18

Brand: inventum Pages: 60

Brand: Turbo Air Pages: 66

Brand: KKT KOLBE Pages: 24

Brand: Hyundai Pages: 26

Brand: DAEWOO ELECTRONICS Pages: 26

Brand: ZANKER Pages: 44

Brand: Lamona Pages: 64

Brand: Frigidaire Pages: 8

Brand: Frigidaire Pages: 2

Brand: Frigidaire Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands