LG MB-3832E Service Manual Download Page 24

Page: 24 / 36

5-14

(TROUBLE 2) Oven does not start cooking even though the timer is set and START pad

is touched.

(TROUBLE 3) Oven seems to be operation but little heat is produced in oven load.

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1.Oven does not

start cooking
count down when
touching START
pad.

2. Fan motor or

oven lamp
do not turn
on.

No continuity.

continuity.

No continuity.

Continuity.

Check the con-
nection between
connector and
P.C.B assembly.

Defective
secondary switch.

Replace
secondary switch.

Defective P.C.B
assembly.

Replace P.C.B
assembly.

Check continuity
of secondary
switch (with
door closed).

Check fan motor.

Check oven lamp.

Abnormal.

Normal.

Defective fan
motor.

Replace fan
motor.

Loose connection.

Connection then
tightly.

CONDITION

CHECK

RESULT

CAUSE

REMEDY

Output is low.

Lower than 90% of
rating voltage.

Normal.

Abnormal.

Measure the
output power.

Disconnect the
wire leads from
relay 2 and check
on and off time
with multitester.

Defective P.C.B
assembly.

Replace P.C.B
assembly.

Decrease in power
source voltage
with load.

Suggest customer
contact local
electric power
utility co. or
qualified
electrician.

Check the
power source
voltage.

Defective
magnetron.

Replace
magnetron.

NOTE: Simple test of power output-conducted by heating one liter water for one min. if available.

Summary of Contents for MB-3832E





































Search results

Summary of Contents for MB-3832E

Reviews:

Related manuals for MB-3832E

Brands by name

Popular brands

LG MB-3832E, Service Manual

Search results

Summary of Contents for MB-3832E

Reviews:

Related manuals for MB-3832E

Brands by name

Popular brands