manualshive.com logo in svg

LG MB-3832E, Service Manual

Share
Download
LG MB-3832E Service Manual Download Page 23

5-13

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1. Fuse blows.

Continuity.

No continuity.

Continuity.

Shorted contact at
the primary switch.

Replace primary
and monitor
switches.

No continuity.

Normal.

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Fuse blows again

Defective high volt-
age transformer.

Replace high volt-
age transformer.

Malfunction of the
monitor switch.

Replace primary
and monitor
switches.

Check continuity
of monitor
switch (with
door closed).

Check continuity
of primary
switch (with
door opened).

Disconnect one
side of the wire
lead connected
from transformer
to the high
voltage
capacitor and
operate the unit.

Replace fuse

(TROUBLE 1) Oven lamp does not turn on when the timer knob is turned with door closed.

NOTE : All these switches must be replaced at the same time. Refer to page 5-6, 5-7

2. Fuse does not

blow.

No continuity.

No continuity.

Replace power
supply cord.

Defective oven
thermostat.

Defective power
supply cord.

Replace oven
thermostat.

Check continuity
of oven
thermostat.

Check continuity
of power supply
cord.

Continuity.

Summary of Contents for MB-3832E





































Reviews:

No comments

Brands by name

Popular brands

Load more brands