LG STUDIO
HOME APPLIANCES
Electrical cable
4 1/2" - 6"
PREPARING ELECTRICAL WIRING
LSDTS9882S
Top Control wi-fi Enabled Dishwasher with
QuadWash™ and TrueSteam®
QUICK INSTALL & CLEARANCES
For full installation directions/clearances please refer to
the corresponding User Manual and Installation Guide.
IMP
O
RT
A
N
T
DIMENSIONS / CLEARANCES / WEIGHT
Product Dimensions (in) (W x H x D)
23 3/4" x 33 5/8" x 24 5/8"
Depth with Door Closed with Handle (in)
27 3/16"
Depth with Door Open (in)
50 1/2"
Carton Dimensions (in) (W x H x D)
28 1/32" x 34 7/8" x 29 5/8"
POWER RATINGS
ENERGY STAR® Qualified
Yes
CEE Tier
1
Energy Use (kWh/Year)
269 kWh/Year
Water Factor (WF)
2.8
Water supply line
6 1/2" - 7 1/4"
•
Make sure the house water supply is turned off before connecting
the dishwasher water lines.
•
Connect the dishwasher to a hot water supply with a temperature range between
120 °F (49 °C) and 149 °F (65 °C). This temperature range provides the best
washing results and shortest cycle time. To prevent damage to dishes, the
temperature should
not exceed 149 °F
(65 °C).
•
When connecting
the dishwasher
water line, sealing
tape or compound
should be used on
pipe threads to
avoid leaks. Tape or
compound should
not be used on
compression fittings.
•
The water supply
tube must be
located in the left
side channel.
•
This dishwasher is designed to fit a standard dishwasher opening.
An opening may be needed on both sides to route plumbing and
electrical connections.
•
Select a location as close to the sink as possible for easy connections to water and
drain lines.
•
To ensure proper drainage,
install the dishwasher no
more than 12 ft. from the
sink.
•
If installing the dishwasher
in a corner, leave a
minimum of 2" between
the dishwasher and the
adjacent wall.
•
To allow for proper
clearance of plumbing and
electrical, use the template
included with the literature
to determine the clearance
on the side of the cabinet
where the cabinet meets
the back wall. Using a 2
1/2" diameter hole saw, drill
a hole in the target area as
shown on the template.
▲
!
WARNING
Don't use existing holes unless they are in the target area. Otherwise, the water
supply and drain hose may be damaged by being crushed or kinked.
▲
!
CAUTION
Failure to properly locate the hole for the water and drain lines may prevent the
dishwasher from installing flush with the cabinets and could result in kinked or
damaged lines. Installation damage is not covered by the warranty, and leaks caused
by improper installation may result in property damage.
NOTE
Use new hoses when connecting to the water supply. Do not reuse old hoses.
PREPARING WATER SUPPLY CONECTION
PREPARING CABINET OPENING
•
Operate this appliance with the correct voltage as shown in your User Manual and
on the rating plate. Connect it to a dedicated, properly grounded branch circuit
which is protected by a time delay fuse. Connect the appliance using 3-wires,
including a ground wire.
•
If an outlet and other
power connector are
used, it should be in
an accessible location
adjacent to and not
behind the dishwasher
and within 4 ft. of the
dishwasher's side.
•
The wiring must be
grounded properly. If in
doubt, have it checked
by a qualified electrician.
Do not connect any other
appliance to the same
outlet.
•
Route the wiring.
•
Make sure the electrical
cable is oriented in the
right side channel.
▲
!
WARNING
•
For personal safety, remove house fuse or open circuit breaker before installation.
•
Do not use an extension cable or adapter with this dishwasher
•
If you find any damage to the dishwasher, contact your retailer or contractor.
© 2021 LG Electronics USA, Inc. All rights reserved. "LG Life’s Good" is a registered trademark of LG Corp. All other product and brand names are trademarks or registered trademarks of their respective owners. Design, features and specifications are subject to
change without notice. Non-metric weights and measurements are approximate. Some features may require Internet access. Content and services may vary by product and are subject to change without notice. 10/12/21
