LG LS501 Instruction Manual Download Page 2

Page: 2 / 40

CAUTION

RISK OF ELECTRIC

SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

dangerous voltage within the product’s enclo-

sure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.
The exclamation point within an equilateral tri-

angle is intended to alert the user to the pres-

ence of important operating and maintenance

(servicing) instructions in the literature accom-

panying the product.

FCC WARNING:

This equipment may generate or

use radio frequency energy. Changes or modifications

to this equipment may cause harmful interference

unless the modifications are expressly approved in the

instruction manual. The user could lose the authority

to operate this equipment if an unauthorized change or

modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply

with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interfer-

ence when the equipment is operated in a commercial

environment.

This equipment generates, uses, and can radi-

ate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may

cause harmful interference to radio communications.

Operation of this equipment in a residential area is

likely to cause harmful interference in which case the

user will be required to correct the interference at his

own expense.

• A suitable conduit entries, knock-outs or glands

shall be provided in the cable entries of this prod-

uct in the end user.

• Caution: Danger of explosion if battery is incor-

rectly replaced. Replaced only with the same or

equivalent type recommended by the manufac-

turer. Dispose of used batteries according to the

manufacturer’s instructions.

Summary of Contents for LS501









































Search results

Summary of Contents for LS501

Reviews:

Related manuals for LS501

Brands by name

Popular brands

LG LS501, Instruction Manual

Search results

Summary of Contents for LS501

Reviews:

Related manuals for LS501

Brands by name

Popular brands