LG LS090HXV2 Installation Manual Download Page 39

Page: 39 / 72

Refrigerant Piping Connections

Due to our policy of continuous product innovation, some specifications may change without notification.

REFRIGERANT PIPING CONNECTIONS

•

Do not bend the piping directly backwards or to the left or right sides without bending it downward first; this will damage the indoor unit

piping.

•

Do not forcibly press the refrigerant piping onto the bottom frame or the front grille; this will damage the indoor unit piping and / or

indoor unit frame.

• Ensure the piping is straight.

Do not kink the piping; this will damage the indoor unit and piping.

Figure 49: Improper Piping Bending.

Figure 50: Keep Piping Straight;

Avoid Kinks.

Piping Installation When Piping is on the Left Side (HEV2

and HXV2)

• See the Electrical System Installation section for information on

how to connect the communication / connection (power) cable from

the outdoor unit.

• For left-side piping, it is recommended that the communication /

power connections are complete before starting the piping connec-

tions.

1. Insert drain hose on left (feature will differ depending on model of

indoor unit).

2. Align the center of the refrigerant piping and corresponding con-

nection as shown on the next page.

3. Place a couple of drops of refrigerant oil on outside of the flare

before assembling.

Do not add any contaminants. Tighten

the flare nut initially by hand.

4. Finish tightening the flare nut with a torque wrench until the

wrench clicks. Follow torque guidelines in the table on the next
page.

:KHQWLJKWHQLQJWKHÀDUHQXWZLWKDWRUTXHZUHQFKHQVXUHWKHGLUHFWLRQ

for tightening follows the arrow on the wrench.

5. Bundle the refrigerant piping, drain hose, and communication /

connection (power) cable together. Ensure that the drain hose is
located at the bottom of the bundle.
• If using a conduit for the power wiring / communications cable,

see the next page.

Figure 51: Piping Installation When Piping is on the Left Side.

Accessing and Positioning the Indoor Unit Piping / Connections (HEV2 and HXV2), continued.

3RVLWLRQLQJWKHGUDLQKRVHDWWKHWRSRIWKHEXQGOHFDQFDXVHFRQGHQVDWHWRRYHUÀRZIURPWKHGUDLQSDQLQWKHLQVLGHRIWKHLQGRRUXQLW

Indoor Unit Connections

Left Side Piping

Drain Hose

Piping

Connection

Cable

Tape

Drain Hose

Summary of Contents for LS090HXV2









































































Search results

Summary of Contents for LS090HXV2

Reviews:

Related manuals for LS090HXV2

Brands by name

Popular brands

LG LS090HXV2, Installation Manual

Search results

Summary of Contents for LS090HXV2

Reviews:

Related manuals for LS090HXV2

Brands by name

Popular brands