background image

2

PARTS PROVIDED

1

BEFORE YOU BEGIN

Remove all tape and packing materials before using
the range. Dispose all plastic bags after unpacking the
range. Never allow children to play with packing
materials.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

If the information in this manual is

not followed exactly, a fire or electrical shock may
result causing property damage, personal injury or
death.

WARNING

• ALL RANGES CAN TIP
• INJURY TO PERSONS   COULD

RESULT

• INSTALL ANTI-TIP BRACKET

PACKED WITH RANGE

• SEE INSTALLATION

INSTRUCTIONS

Important Notes to the Installer

•  Read all instructions contained in these installation

instructions before installing range.

•  Remove all packing materials from the oven

compartments before connecting the electrical
supply to the range.

•  Observe all governing codes and ordinances.
•  Be sure to leave these instructions with the consumer.

Important Note to the Consumer

Keep these instructions with your owner’s manual for
future reference.
•  As when using any appliance generating heat, there

are certain safety precautions you should follow. 

•  Be sure your range is installed and grounded

properly by a qualified installer or service technician.

•  Make sure the wall coverings around the range can

withstand the heat generated by the range.

•  To eliminate the need to reach over the surface

elements, cabinet storage space above the elements
should be avoided.

TOOLS NEEDED

Part 1

SAFETY

PREPARE TO INSTALL THE RANGE

PARTS NOT PROVIDED

Summary of Contents for LRE30451

















Reviews: