LG LMX21981 Series Training Manual Download

Page: 21 / 78

LMX21981xx

REFRIGERATOR

LMX21981xx Page

TRAINING

MANUAL

RESETTING THE FILTER INDICATOR

Press and hold the LIGHT/FILTER button
for more than 3 seconds to reset the filter
indicator after the water filter has been
replaced.

NOTE: Replace the filter when the water
filter indicator light reaches 0 or whenever
the water or ice cube taste deteriorate
noticeably.

To purchase replacement water filter cartridges, visit your local appliance dealer or parts
distributor. You can also call 1-877-714-7486.

The replacement water filter cartridge’s part number is 5231JA2006A.

ACTIVATING ICE PLUS

Press the ICE+PLUS button once to

activate the ICE+PLUS function.
The ICE+PLUS icon on the display panel

will illuminate when activated.

The ICE+PLUS function runs the freezer

compartment at the coldest setting for a

24-hour period to increase icemaking by
up to about 20%, and then turns off

automatically.

NOTE:

Press the button again to cancel the
ICE+PLUS function.

DIAGNOSTIC FAILURE DETECTION

The diagnostic function automatically detects problems with your refrigerator, and a
diagnostic code will appear in the display.

Summary of Contents for LMX21981 Series















































































Search results

Summary of Contents for LMX21981 Series

Reviews:

Related manuals for LMX21981 Series

Brands by name

Popular brands

LG LMX21981 Series, Training Manual

Search results

Summary of Contents for LMX21981 Series

Reviews:

Related manuals for LMX21981 Series

Brands by name

Popular brands