background image

Your Safety First

• MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT.

– Mount the oven against a flat, vertical wall, so it is supported by the wall. The wall should be constructed of

minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.

– ATTACH (See note on page 

4

) the two lag screws supporting the oven to a vertical, 2" x 4" wall stud.

– DO NOT mount the microwave oven to an island or peninsula cabinet.

– BE SURE the upper cabinet and rear wall structures can support 150 lbs., plus the weight of any

items you place inside the oven or upper cabinet.

– Locate the oven away from strong draft areas, such as windows, doors, and strong heating vents.

– BE SURE you have enough space. See Figure 4 below for minimum vertical and horizontal clearance.

 Before you begin installing the oven, PLACE A PIECE OF THE CARTON OR OTHER HEAVY

MATERIAL (a blanket) over the countertop or cooktop to protect it. Do not use a plastic cover.

Failure to protect these surfaces could result in property damage.

30" min. cabinet opening width

30" min. clearance from bottom

of cabinet to cooking surface

or countertop before installation.

Grounded Outlet

(inside upper cabinet)

Power Supply Cord Hole

(Use templates included

 with installation instructions)

If 

y

ou do not mount the 

o

ven as instructed,

y

ou risk personal injury and/or property dama

g

e.

NOTE: Maximum cabinet depth is 13".

SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.

• DO NOT EXPOSE YOURSELF TO EXCESSIVE MICROWAVE ENERGY!

– DO NOT try to operate the microwave oven with the door open.

– DO NOT tamper with or defeat the safety interlocks.

– DO NOT place objects between the microwave oven front face and the door.

– DO NOT allow soil or cleaner residue to build up on the flat surfaces around 

– DO NOT operate the microwave oven if it is damaged.

– The microwave oven door must close properly to operate safely.

– DO NOT USE THE MICROWAVE OVEN:

the microwave oven door.

 If the door is bent.

 If the hinges or latches are broken or loose.

 If the door seals, sealing surfaces or glass is broken.

– DO NOT ATTEMPT TO ADJUST OR REPAIR THE OVEN YOURSELF!

It should be adjusted and repaired by a qualified technician who can check for microwave leakage after

repairing the oven.

If 

y

ou do not use the micr

ow

ave 

o

ven as instructed,

y

ou could be exposed to excessive micr

ow

ave ener

gy

.

W A R N I N G

w

W A R N I N G

w

w

CAUTION

– 

3

 –

Figure 4

Summary of Contents for LMV1831BDLG

















Reviews: