LG LGSWFAC81 Manual Download Page 7

requirements  required  with  this  module  installed  (for  example,  digital  device  emissions,  PC 
peripheral requirements, etc.). 

End Product Labeling 

The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC 
Certification Number are not visible when the module is installed inside another device, then the 
outside of the device into which the module is installed must also display a label referring to the 
enclosed module. In that case, the final end product must be labeled in a visible area with the 
following: 
“Contains FCC ID: 

BEJLGSWFAC81

 

“Contains IC: 

2703H-LGSWFAC81

” 

2. IC

RSS-GEN, Sec. 7.1.3 – (licence-exempt radio apparatus)  

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to 
the following two conditions: (1) this device may not cause interference, and (2) this device must 
accept any interference, including interference that may cause undesired operation of the device. 
Le  présent  appareil  est  conforme  aux  C NR  d’Industrie  Canada  applicables  aux  appareils  radio 
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit 
pas  produire  de  brouillage,  et  (2)  l’utilisateur  de  l’appareil  doit  accepter  tout  brouillage 
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. 

RF Exposure 

The antenna (or antennas) must be installed so as to maintain at all times a distance minimum 
of at least 

20

 cm between the radiation source (antenna) and any individual. This device 

may not be installed or used in conjunction with any other antenna or transmitter. 

l'exposition aux RF 

L’antenne  (ou  les  antennes)  doit  être installée de  façon  à  maintenir  à tout instant  une 
distance minimum de au moins 

2

0 cm entre la source de radiation (l’antenne) et toute personne 

physique. 

Caution:

 Any changes or modifications to this device not explicitly approved by manufacturer could 

void your authority to operate thisequipment.Attention: 

Les  changements  ou  modifications  de  cet  appareil  non  expressément  approuvé  par  le  fabricant 
peuvent annuler votre droit à utiliser cet équipement. 

Summary of Contents for LGSWFAC81









Reviews: