background image

3

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

Always comply with the following precautions to avoid dangerous situations and ensure peak
performance of your product

WARNING

It can result in serious injury or death when the directions are ignored

CAUTION

It can result in minor injury or product damage when the directions are ignored

WARNING

• Installation or repairs made by unqualified persons can result in hazards to you and others.

• Installation of all field wiring and components MUST conform with local building codes or, in

the absence of local codes, with the National Electrical Code 70 and the National Building
Construction and Safety Code or Canadian Electrical code and National Building Code of
Canada.

• The information contained in the manual is intended for use by a qualified service technician

familiar with safety procedures and equipped with the proper tools and test instruments.

• Failure to carefully read and follow all instructions in this manual can result in equipment

malfunction, property damage, personal injury and/or death.

Installation

• Always perform grounding. 

- Otherwise, it may cause electrical shock. 

• Don’t use a power cord, a plug or a loose socket which is damaged. 

- Otherwise, it may cause a fire or electrical shock.

• For installation of the product, always contact the service center or a professional installation

agency. 
- Otherwise, it may cause a fire, electrical shock, explosion or injury.

• Securely attach the electrical part cover to the indoor unit and the service panel to the outdoor unit.

- If the electrical part cover of the indoor unit and the service panel of the outdoor unit are not

attached securely, it could result in a fire or electric shock due to dust, water, etc.

• Always install an air leakage breaker and a dedicated switching board. 

- No installation may cause a fire and electrical shock.

• Do not keep or use flammable gases or combustibles near the air conditioner. 

- Otherwise, it may cause a fire or the failure of product.

• Ensure that an installation frame of the outdoor unit is not damaged due to use for a long time. 

- It may cause injury or an accident.

• Do not disassemble or repair the product randomly. 

- It will cause a fire or electrical shock.

• Do not install the product at a place that there is concern of falling down. 

- Otherwise, it may result in personal injury.

• Use caution when unpacking and installing.

- Sharp edges may cause injury.

• Use a vacuum pump or Inert (nitrogen) gas when doing leakage test or air purge. Do not compress

air or Oxygen and Do not use Flammable gases. Otherwise, it may cause fire or explosion. There is
the risk of death, injury, fire or explosion.

!

!

!

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

Summary of Contents for LDN097HV4






















Reviews: