background image

4

SAFETY

•   Using an extension cord to connect the power is prohibited.

The way to connect the power cord and plug directly is strongly recommended.

•   Electrical ground is required on this appliance.
•  You should make sure that the power cord is not pinched by the range or heavy objects.

-  Failure to do so can result in serious burns or electrical shock.

•  You never remove the protection cover covering the rear of lower oven.

-   Failure to do so can result in serious damage to power cord. The damage causes serious burns and electric 

shock.

•   The middle (neutral or ground) wire of a 3 wire power cord or a 3 wire conduit has to be connected to the 

middle post of the main terminal block. The remaining two wires of the power cord or conduit have to be 
connected to the outside posts of the main terminal connection block.

-   Failure to do so can result in electrical shock, severe personal injury or death.

•   Only a 4-conductor power-supply cord kit rated 120/240 volts, 50 amperes and marked for use with 

ranges with closed-loop connectors or open-end spade lugs with upturned ends shall be used. The 
middle (neutral) wire of the power cord or 4-wire conduit has to be connected to the middle post of 
the main terminal block. The other two wires of the power cord or conduit have to be connected to the 
outside posts of the main terminal connection block. The 4th ground wire must be connected to the 
frame of the range with the ground screw.

-  Failure to do so can result in electrical shock, severe personal injury or death.

 WARNING

•  You should put on gloves during the installation procedure.

-  Failure to do so can result in bodily injury.

•   You should make sure that the wall covering, countertop and cabinets around the range can withstand 

the heat (up to 194°F) generated by the range.

-   Discoloration, delamination or melting may occur.
-   This range has been designed to comply with the maximum allowable wood cabinet temperatures of 194°F.

•   Cabinet storage space located above the surface units should be avoided.
•   You should install a range hood that projects horizontally a minimum of 5 inches beyond the bottom of 

the cabinets. If cabinet Storage is to be provided.

-  The risk of burns or fire by reaching over the heated surface elements can be reduced.

•   You should not install the range in the humid place. Splashing the range with water or any electrolyte can 

result in electrical shock.

•  You should not let cooking grease or flammable material accumulate in or near the range.

-   Failure to do so can result in serious burns.

 CAUTION

Summary of Contents for LDE3011ST












Reviews: