LG KG225 Service Manual Download Page 95

Page: 95 / 126

- 96 -

9. ENGINEERING MODE

9.1 BB Test [MENU 1]

9.1.1 CAMERA

This menu is to test the Camera.

1) Main LCD preview : It shows the picture on Main LCD.

9.1.2 LED

This menu is to test the LED.

1) Green On

2) Green Off

3) Red On

4) Red Off

9.1.3 LCD

1) COLOUR : WHITE, RED, GREEN, BLUE, BLACK

2) Contrast Value

9.1.4 Backlight

This menu is to test the LCD Backlight and Keypad EL Backlight.

1) Backlight on : LCD Backlight and Keypad EL Backlight light on at the same time.

2) Backlight off : LCD Backlight and Keypad EL Backlight light off at the same time.

3) Backlight value : This controls brightness of Backlight. When entering into the menu, the present

backlight-value in the phone is displayed. Use Left/Right key to adjust the level of

brightness. The value of the brightness set at last will be saved in the NVRAM.

9.1.5 Buzzer

This menu is to test the melody sound.

1) Melody on : Melody sound is played through the speaker.

2) Melody off : Melody sound is off.

9.1.6 Vibrator

This menu is to test the vibration mode.

1) Vibrator on : Vibration mode is on.

2) Vibrator off : Vibration mode is off.

Summary of Contents for KG225































































































































Search results

Summary of Contents for KG225

Reviews:

Related manuals for KG225

Brands by name

Popular brands

LG KG225, Service Manual

Search results

Summary of Contents for KG225

Reviews:

Related manuals for KG225

Brands by name

Popular brands