LG KF310 Service Manual Download Page 20

Page: 20 / 174

LGE Internal Use Only

3. TECHNICAL BRIEF

- 21 -

3.5.2 VCTCXO (X1000 :DAS321SCE-19.2M)

The Voltage Controlled Temperature Compensated Crystal Oscillator (VCTCXO) provides the

reference frequency for all RFIC synthesizers as well as clock generation functions within the

MSM6245 IC. The oscillator frequency is controlled by the MSM6245 ICs. TRK_LO_ADJ pulse density

modulated signal in the same manner as the transmit gain control TX_AGC_ADJ. A two-pole RC

lowpass filter is recommended on this control line. The PM6658 IC controls the handset power-up

sequence, including a special VCTCXO warmup interval before other circuits are turned on. This

warm-up interval (as well as other TCXO controller functions) is enabled by the MSM TCXO_EN line .

The PM6658 IC VREG_TCXO regulated output voltage is used to power the VCTCXO and is enabled

before most other regulated outputs.

Any GSM mode power control circuits within the MSM6245 IC require a reference voltage for proper

operation and sufficient accuracy. Connecting the PM6658 IC REF_OUT directly to the MSM6275 IC

GSM_PA_PWR_CTL_REF provides this reference. This sensitive analog signal needs a 0.1 µF low

frequency filter near to MSM side, and isolate from digital logic and clock traces with ground on both

sides, plus ground above and below if routed on internal layers.

3.5.3 Front-End Module (FL1000 : DGM129M01)

This equipment uses a single antenna to support all handset operating modes, with an antenna switch

module select the operating frequency and band. UMTS operation requires simultaneous reception

and transmission, so the UMTS Rx/Tx connection is routed to a duplexer that separates receive and

transmit signals. The active connection is MSM-selected by three control lines (GPIO[9], GPIO[10],

and GPIO[11]). These GPIOs are programmed to be ANT_SEL0, ANT_SEL1, and ANT_SEL2

respectively.

ANT_SEL0

ANT_SEL1

ANT_SEL2

GSM850/EGSM TX

HIGH

LOW

HIGH

PCN/PCS TX

HIGH

LOW

WB2100

HIGH

LOW

EGSM RX

LOW

HIGH

LOW

PCN RX

LOW

HIGH

PCS RX

LOW

HIGH

LOW

[Table 3.5.3.1] Front End Module control logic

Z3X-BOX.COM

Summary of Contents for KF310
































































































































































Search results

Summary of Contents for KF310

Reviews:

Related manuals for KF310

Brands by name

Popular brands

LG KF310, Service Manual

Search results

Summary of Contents for KF310

Reviews:

Related manuals for KF310

Brands by name

Popular brands