background image

How to Use the Discs

When using CD-ROM discs, CD-R discs, DVD discs or CD-RW discs, don’t attach
any stickers or labels to the discs. It could cause read and write errors, but data on
the disc may be lost due to damage to the disc itself.

Emergency Eject

This drive has a feature that allows the CD to be ejected manually if this becomes 
necessary such as failure of the drive or a power outage. 

NOTE:

Don’t use this feature 

except 

in an emergency.

1)

Turn the power to OFF.

2)

Poke a fine-tipped object (such as a straightened heavy duty paper clip) into the
small hole above the eject button. The front door will pop open and the disk tray
will come partway out.

3)

Pull the front door to open it all the way, then grip the disc tray between thumb
and forefinger and gently pull it straight out.

*  If you cannot get a good grip on the disc tray with your fingers, use a steel binder

clip or spring clamp to pull it out.

9

The Discs in this unit operate at a very
high speed! DO NOT use damaged,
cracked or warped discs. The drive’s 
optical unit may be damaged if they
break.

DO NOT use non-standard discs. NON-standard discs may not play or store data
properly. 

NOTE: 

This feature is a last measure to be

used only in an emergency. 
Using it excessively will cause malfunction.

Summary of Contents for GSA-H44N
















Reviews: