LG GoldStar MS-110YG Page 25 Service Manual Download | Manualshive

Page: 25 / 35

background image

5-15

CONDITION

CHECK

RESULT

CAUSE

REMEDY

No microwave
oscillation.

No continuity.

Continuity.

Abnormal

Defective high
voltage
transformer.

Replace high
voltage
transformer.

Normal

Defective PCB
assembly.

Replace PCB
assembly.

Disconnect the
wire leads from
relay 2 and
check continuity
of relay 2.
(Operate the unit)

Check high vol-
tage transformer

Output is full power
when you set lower
power level.

Abnormal.

Defective PCB
assembly.

Replace PCB
assembly.

Disconnect the
wire leads from
relay 2 and check
continuity relay 2.
(Operate the unit)

Abnormal

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Normal

Check high vol-
tage capacitor.

Abnormal

Defective high
voltage diode.

Replace high
voltage diode.

Normal

Check high vol-
tage diode.

Abnormal

Defective
magnetron.

Replace
magnetron.

Check
magnetron.

(TROUBLE 5) No microwave oscillation even though oven lamp and fan motor run.

(Display operates properly)

NOTE : • Make sure the wire leads correct position.

• When Removing the wire leads from the parts, be sure to grasp the connector, not the wires.
• When removing the magnetron, be sure to install the magnetron gasket in the correct position

and in good condition.

«
...
23
24
25
26
27
...
»

Summary of Contents for GoldStar MS-110YG




































Reviews:

No comments

Related manuals for GoldStar MS-110YG

Brand: Panasonic Pages: 110

Brand: Garland Pages: 32

Brand: Garland Pages: 2

Brand: Garland Pages: 32

Brand: Teka Pages: 14

B46VT64 0 Series

Brand: NEFF Pages: 64

Brand: Monogram Pages: 52

Brand: GE Pages: 48

Brand: Caso Pages: 179

Brand: Jenn-Air Pages: 32

SpeedWave GSWWA12S1SA10

Brand: Galanz Pages: 32

Brand: NEFF Pages: 32

Brand: shelolab Pages: 21

Double Built in Oven

Brand: Rangemaster Pages: 16

Brand: Omega Pages: 20

Brand: Hyundai Pages: 25

Brand: Cookology Pages: 25

Brand: Sandstrom Pages: 208

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands