LG GoldStar MA1152B Service Manual Download Page 19 | Manualshive

Page: 19 / 33

background image

5-9

NOTE: When testing the magnetron, be sure to install the magnetron gasket

in the correct position and be sure that the gasket is in good condition.

Antenna

Gasket

Chassis

Filament

HIGH VOLTAGE
CAPACITOR

Measure the resistance.
(Ohm-meter scale: Rx1000)
• Terminal to terminal.

Normal: Momentarily indicates

several ohms, and
then gradually returns
to infinite.

Normal: Infinite.

Normal: Continuity.
Abnormal: Infinite.

Normal: Infinite.
Abnormal: Continuity.

Measure the resistance.
(Ohm-meter scale: Rx1000)
• Terminal to case.

Measure the continuity (Forward).
(Ohm-meter scale: Rx10000)

Measure the continuity (Reverse).
(Ohm-meter scale: Rx10000)

HIGH VOLTAGE
DIODE

NOTE :
Some inexpensive meters
may indicate infinite
resistance in both direction.

COMPONENTS TEST

PROCEDURE RESULTS

«
...
17
18
19
20
21
...
»

Summary of Contents for GoldStar MA1152B


































Reviews:

No comments

Related manuals for GoldStar MA1152B

Brand: Candy Pages: 25

Profile Advantium PSA2200R

Brand: GE Pages: 80

Profile Advantium PSB9240DFBB

Brand: GE Pages: 3

Brand: GE Pages: 40

Brand: Jenn-Air Pages: 8

Brand: Kuppersbusch Pages: 18

Brand: Thermador Pages: 68

Brand: Garland Pages: 16

Brand: saro Pages: 9

Brand: NEFF Pages: 40

Brand: Silverline Pages: 45

Brand: Jenn-Air Pages: 16

Spacemaker JNM1541DN

Brand: GE Pages: 3

Brand: Jenn-Air Pages: 8

Brand: Brandt Pages: 57

Brand: Daewoo Pages: 14

Brand: ZANKER Pages: 92

Brand: Belling Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands