LG CRD-8483B Service Manual Download Page 19

Page: 19 / 25

• IC501 MT1198CE

Pin Description

Pin No.

Symbol

Type

Description

Data PLL Interface

Reference voltage

Ground pin for data PLL and related analog circuitry.

The output of VCO integrator.

The negative input terminal of VCO integrator.

The output of loop filter amplifier.

The negative input terminal of loop filter amplifier.

Current reference input. It generate reference current for data PLL.
Connect an external 15K resistor to this pin and PLLVSS.

Phase comparator output. Output the phase difference of EFM and Pck.
Sink or (source) a constant current to loop filter over this pin when phase
difference occurs. Otherwise, this pin is high impedance.

Power for data PLL and related analog circuitry.

Programmable bi-direction I/O.
Alternate function : T1.Timer 1 input.

Programmable bi-direction I/O.
Alternate function : T0. Timer 0 input.

Ground pin for internal digital circuitry.

Programmable bi-directional I/O.
Alternate function : INT0_. External interrupt 0.

Programmable bi-directional I/O.
Alternate function : TXD. Serial transmit data.

Programmable bi-directional I/O.
Alternate function : RXD. Serial receive data.

Power pin for internal digital circuitry.

Programmable bi-directional I/O.
Alternate function : A16. Address bit 16 output.

Programmable bi-directional I/O.
Alternate function : A[15:8]. Upper address bus input/output.

WR_. Data write signal. The pin is dedicated for WR_ function, and the
programmable I/O function is removed.

Programmable store enable output, active low. PSEN_ enables the
external ROM output port.
Alternate function : Programmable output.

Ground pin for internal digital circuitry.

Address latch enable output, active high.
Alternate functiion : Programmable GPIO.

Programmable bi-directional I/O.
Alternate function : AD[7.0]. Lower adress/data bus output for external
device.

Lower address bus output for external device.
Alternate function : Pfogrammable output.

VBDPLL

PLLVSS

LPIO

LPIN

LPFO

LPFN

IREF

PDO

PLLVDD

UP3_5/UT1

UP3_4/UT0

DGND

UP3_2/

UINT0

UP3_1/

UTXD

UP3_0/

URXD

DVDD

UP1_0/

UA16

UP2_[7:0]/

UA[15:8]

UP3_6/

UWR_

UPSEN_/

DGND

UALE/

IO10

UP0_[7:0]/

UAD[7:0]

UA[7:0]/

0[18:11]

25, 27, 28, 29,

30, 31, 33, 35

38-45

46-53

Anallog Output

Ground

Analog Output

Analog Input

Analog Output

Analog Input

Analog output

Analog Power(5V)

TTL I/O, Slew rate

50K pull_up

TTL I/O, Slew rate

50K pull_up

Ground

TTL I/O, Slew rate

50K pull_up

TTL I/O, Slew rate

50K pull_up

TTL I/O, Slew rate

50K pull_up

Power(5V)

TTL I/O, Slew rate

50K pull_up

TTL I/O, Slew rate

50K pull_up

TTL I/O, Slew rate

SMT, 50K pull_up

TTL I/O

50K pull_up

Ground

TTL I/O

50K pull_up

TTL I/O, Slew rate

Turbo 8032 Interface

Summary of Contents for CRD-8483B


























Search results

Summary of Contents for CRD-8483B

Reviews:

Related manuals for CRD-8483B

Brands by name

Popular brands

LG CRD-8483B, Service Manual

Search results

Summary of Contents for CRD-8483B

Reviews:

Related manuals for CRD-8483B

Brands by name

Popular brands