LG CodePlus HCS6300 Series Installation & Setup Manual Warranty Download Page 40

Page: 40 / 52

206-4122

Configuration Options via Command Line (Cont.)

Transcoder Menu Commands

The following subsections describe how to access and use the Transcoder Menu commands.

Note:

Refer to the Installation & Setup Guide for the applicable transcoder cards for further

information on transcoder configuration options.

Access the Transcoder Menu

1. Access the HCS6300 Main Menu as described on page 31.
2. At the

[Main] Command >

prompt, type

card

and press

Enter

3. At the

Enter card number (1-12) >

prompt, type the chassis slot number of the

transcoder card for which you wish to access configuration options. Then, press

Enter

The system identifies the card type and then displays a command prompt for the card

menu, for example:

Card #1 is: HCS7710

[HCS7710 (1)] Command >

4. At the

Command >

prompt, either:

• Press

Enter

to display the card menu (see example below).

• Type the desired command and press

Enter

Note:

You can always press

Enter

at the

Command >

prompt to display the Transcoder

Menu.

Example: Transcoder Menu

------------

HCS7710 Menu

------------

hwid Read Hardware ID

ver Read Software Versions

caget

Read Content Advisory Messages Setting

caset

Enable/Disable Content Advisory Messages

bits Read MUX Bitrates

pi Install PI Key

Reload PI Key

cksum Read PI Key Checksum

stb Satellite Receiver Menu

upd Update Firmware

irst Internal Reset

ret Return to Main Menu
[HCS7710 (1)] Command >

* These commands are applicable to HCS7700 and HCS7710 cards only. Refer to the LG Service

Bulletin on Content Advisory configuration options for further information.

Summary of Contents for CodePlus HCS6300 Series




















































Search results

Summary of Contents for CodePlus HCS6300 Series

Reviews:

Related manuals for CodePlus HCS6300 Series

Brands by name

Popular brands

LG CodePlus HCS6300 Series, Installation & Setup Manual Warranty

Search results

Summary of Contents for CodePlus HCS6300 Series

Reviews:

Related manuals for CodePlus HCS6300 Series

Brands by name

Popular brands