manualshive.com logo in svg

LG ARNH963K2A2, Installation Manual

Share
Download
LG ARNH963K2A2 Installation Manual Download Page 39

System Set-Up   

Hydro Kit

Installation Manual 

39

ENGLISH

Group Control Setting

Group Control

- Wired remote controller 1 + Many of 

Hydro Kit

1. It is possible to connect 16 indoor units(Max) by one wired remote controller.

Set only one indoor unit to Master, set the others to Slave.

2. You can connect all the types of 2nd generation indoor units .
3. It is possible to use wireless remote controller at the same time.
4. It is possible to connect Dry Contact and Central controller at the same time.

- The Master indoor unit is possible to recognize Dry Contact and Central Controller only.
- In case of Central controller and Group controller at the same time, it is possible to connect

standard 2series indoor units or later since Feb. 2009. 

- In case of Central controller setting, the Central controller can control indoor units after setting

only the address of master indoor unit.

- Slave indoor unit will be operated like master indoor unit.
- Slave indoor unit can not be individually controlled by Central controller.
- Some remote controller canʼt perform with Dry Contact and Central controller at the same time.

So contact us further information about it.

- Dip Switch in PCB 

Display Error Message

Only connect serial signal and GND lines

between slave indoor unit

Slave

Slave

Master

Slave

Master

GND
Signal
12 V

¿

Master Setting
- No. 1 Off

¡

Slave Setting
- No. 1 On

Summary of Contents for ARNH963K2A2
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands