LG A7UW40GFA0 Installation Manual Download

Page: 34 / 39

FUNCTION

ENGLISH

Saving Power Consumption Current level.

Night Quiet Mode

Night Quiet Mode operation lowers the noise level of the outdoor unit by changing the comp
frequency and fan speed. This function is operated all night long.

Setting Procedure

Set the DIP Switch as follow after shutting the power source down.

Reset the power.

Night Quiet Mode with Mode Lock.

Saving Power Consumption with Mode Lock.

Phase

1 ¢

Model

40 k

48 k

56 k

Step1(A) 22

Step2(A) 18

Saving Power

Consumption (step 1)

+ Mode Lock (Cooling)

Saving Power

Consumption (step 2)

+ Mode Lock (Cooling)

Saving Power

Consumption (step 1)

+ Mode Lock (Heating)

Saving Power

Consumption (step 2)

+ Mode Lock (Heating)

Mode Lock (Cooling)

+ Night Quiet Mode

(step 1)

Mode Lock (Cooling)

+ Night Quiet Mode

(step 2)

Step 1

Step 2

Noise level :Step 1 > Step 2

• If comp frequency and fan speed are down, the cooling capacity may decrease accordingly.

• This function is only available for Cooling Mode.

• If you want to stop the Night Quiet Mode, Change the DIP Switch.

• If operating indoor unit is set by the fan speed “Power”, Night Quiet Mode will be stopped

until fan speed “Power” is changed.

CAUTION

Summary of Contents for A7UW40GFA0








































Search results

Summary of Contents for A7UW40GFA0

Reviews:

Related manuals for A7UW40GFA0

Brands by name

Popular brands

LG A7UW40GFA0, Installation Manual

Search results

Summary of Contents for A7UW40GFA0

Reviews:

Related manuals for A7UW40GFA0

Brands by name

Popular brands