LG A3UQ24GFD0 Installation Manual Download Page 17

Page: 17 / 39

FLARING WORK AND CONNECTION OF PIPING

ENGLISH

Indoor unit installation

Hook the indoor unit onto the upper portion of

the installation plate.(Engage the two hooks of

the rear top of the indoor unit with the upper

edge of the installation plate.) Ensure that the

hooks are properly seated on the installation

plate by moving it left and right.

Press the lower left and right sides of the unit

against the installation plate until the hooks

engage into their slots(clicking sound).

Connecting the pipings to the indoor unit and

drain hose to drain pipe

- Align the center of the pipings and sufficient-

ly tighten the flare nut by hand.

- Tighten the flare nut with a wrench.

- When extending the drain hose at the indoor

unit, install the drain pipe.

Wrap the insulation material around the con-

necting portion.

- Overlap the connection pipe insulation mate-

rial and the indoor unit pipe insulation materi-

al. Bind them together with vinyl tape so that

there is no gap.

- Wrap the area which accommodates the rear

piping housing section with vinyl tape.

Outside diameter

inch

Ø6,35

1/4

1,1 – 1,3

Ø9,52

3/8

1,5 – 1,7

Ø12,7

1/2

1,6 – 1,8

Ø15,88

5/8

1,6 – 1,8

Ø19,05

3/4

1,9 – 2,1

Drain hose

Connecting

Indoor unit tubing

Flare nut

Pipings

Torque wrench

Indoor unit tubing

Spanner (ﬁxed)

Connection pipe

Flare nut

Vinyl tape(narrow)

Adhesive

Drain pipe

Indoor unit drain hose

Plastic bands

Insulation material

Vinyl tape(narrow)

Connection
pipe

Connecting cable

Vinyl tape
(wide)

Wrap with vinyl tape

Indoor
unit pipe

Pipe

Summary of Contents for A3UQ24GFD0








































Search results

Summary of Contents for A3UQ24GFD0

Reviews:

Related manuals for A3UQ24GFD0

Brands by name

Popular brands

LG A3UQ24GFD0, Installation Manual

Search results

Summary of Contents for A3UQ24GFD0

Reviews:

Related manuals for A3UQ24GFD0

Brands by name

Popular brands