LG 86UH5C Service Manual Download Page 6

Page: 6 / 50

- 6 -

LGE Internal Use Only

Only for training and service purposes

SPECIFICATION

1. Application range

This specification is applied to the LW68E chassis.

2. Requirement for Test

Each part is tested as below without special appointment.

1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F),

CST: 40 °C ± 5 °C

2) Relative Humidity: 65 % ± 10 %

3) Power Voltage

: Standard input voltage (AC 100-240 V~, 50/60 Hz)

* Standard Voltage of each products is marked by models.

4) Specification and performance of each parts are followed

each drawing and specification by part number in accord

ance with BOM.

5) The receiver must be operated for about 20 minutes prior to

the adjustment.

No.

Item

Specification

Remarks

Supported Sync. Type

Digital

Operating Frequency

Horizontal

30 ~ 83 kHz

Vertical

23 ~ 71 Hz

Resolution

Max.

HDMI1/2: 3840×2160 @ 60Hz

HDMI3/DP: 3840×2160 @ 30Hz

OPS/DVI: 1920×1080 @ 60Hz

Recommend

HDMI1/2: 3840×2160 @ 60Hz

HDMI3/DP: 3840×2160 @ 30Hz

OPS/DVI: 1920×1080 @ 60Hz

3.1. DVI-D, HDMI, Diplay Port, OPS Specification

3. General Specification

Summary of Contents for 86UH5C


















































Search results

Summary of Contents for 86UH5C

Reviews:

LG 86UH5C, Service Manual, Page: 6 / 50

Search results

Summary of Contents for 86UH5C

Reviews: