LG 65UP7670PUC Page 13 Service Manual Download

Page: 13 / 84

- 13 -

Only for training and service purposes.

ASSEMBLY / DISASSEMBLY GUIDE (SET)

■ Disassembly

1. After Screw & Holder Disassemble, please remove Cover Assy., Rear from Module.

(1) Remove Screw.

(2) Remove Latch(Holder)

Screw 10EA(M3*5.5)

Screw 2EA(P4*10)

65UP80 Latch 10 Points

: Latch location(Holder_8EA / Side AV_2EA)

* Remove both the right side latch and left side latch.

Hold the Right(Left) bottom handle and lift the B/C.

At the same time, gently pushing the push points.

(Separate the B/C from bottom to top direction)

(first lower side, and then the upper side.)

* If push with strong force from left side, Side Latch

will break.

PUSH

PULL

Step1) Lower Right(Left) Side

Step2) Upper Right(Left) Side

PUSH

PULL

Pull

Latch

Push

Pull

Latch

Push

It is easy to pull it to put your
finger in the groove.

An illustrative

photograph

Summary of Contents for 65UP7670PUC


















































































Search results

Summary of Contents for 65UP7670PUC

Reviews:

Related manuals for 65UP7670PUC

Brands by name

Popular brands

LG 65UP7670PUC, Service Manual

Search results

Summary of Contents for 65UP7670PUC

Reviews:

Related manuals for 65UP7670PUC

Brands by name

Popular brands