LG 32LG40 Series Training Manual Download Page 17

Page: 17 / 73

LCD DV August 2008 32LG40

1) Create an LG_DTV folder on the USB Flash Drive

2) Copy new software (xxx.epk) to "LG_DTV"

folder. Make sure to have correct software file.

3) With TV turned on, insert USB flash drive.
4) You can see the message

“TV Software Upgrade” (See figure to right)

5) Cursor left and highlight "START" Button and

push “Enter” button using the remote control.

6) You can see the download progress Bar.
7) Do not unplug until unit has automatically

restarted.

8) When download is completed, you will see

“COMPLETE”.

9) Your TV will be restarted automatically.

Software Upgrade Procedure

Shows the

Currently

Installed

Version

Shows the

Software

Version

found on the

USB Flash

Drive

Shows the

Software file found

on the USB Flash

Drive

* CAUTION:
Do not remove AC power or the USB Flash Drive.
Do not turn off Power, during the upgrade
process.

Summary of Contents for 32LG40 Series










































































Search results

Summary of Contents for 32LG40 Series

Reviews:

Related manuals for 32LG40 Series

Brands by name

Popular brands

LG 32LG40 Series, Training Manual

Search results

Summary of Contents for 32LG40 Series

Reviews:

Related manuals for 32LG40 Series

Brands by name

Popular brands