background image

2

Floor Standing type Air Conditioner

Floor Standing Type Air Conditioner Installation Manual

TABLE OF CONTENTS

Safety Precautions

..........................................................................................3

Installation of Indoor, Outdoor Unit

..............................................................6

1) Selection of the best location.................................................................................................................................6

2) Indoor Unit Installation ...........................................................................................................................................8

3) Outdoor unit installation .........................................................................................................................................8

4) Refrigerant amount ................................................................................................................................................8

5) Installation guide at the seaside ............................................................................................................................9

6) Installation method procedure..............................................................................................................................10

7) Preparation of installation parts and tools ...........................................................................................................11

8) Preparation of piping............................................................................................................................................12

9) Connection of piping ............................................................................................................................................13

10) Precautions in bending ......................................................................................................................................13

11) Connecting the cable to the indoor unit .............................................................................................................14

12) Connecting the piping to the outdoor unit..........................................................................................................15

13) Connecting the cable to the outdoor unit...........................................................................................................15

14) Power supply and wiring ....................................................................................................................................16

15) Vacuum drying of the connecting pipes and the indoor unit..............................................................................17

16) Form the pipe.....................................................................................................................................................18

Final Check and Test Run

..........................................................................................19

OUT-LINE OF INSTALLATION

Summary of Contents for 20k





















Reviews: