LG SIGNATURE WD205C Series Owner'S Manual Download

Page: 9 / 35

ENGLISH

INSTALLATION INSTRUCTIONS

UNPACKING AND REMOVING

SHIPPING MATERIAL

1. After removing the carton and shipping material,

lift the washer off the foam base. Make sure the
plastic tub support comes off with the base and
is not stuck to the bottom of the washer.

Plastic Tub
Support

Carton Base

If you must lay the washer down to remove the base
packaging materials, always protect the side of the
washer and lay it carefully on its side. DO NOT lay
the washer on its front or back.

2. Save the foam block for future use. If the washer

must be moved in the future, the foam block
will help prevent damage to the washer during
transportation.

NOTE:

To prevent damage, do not remove

the foam block until the washer is at the final
location.

3. Turn the top cover about 180 degrees. Cover the

upper hole with the

top cover and install 4 short

screws (included in packing box) to fix it in place.

Top cover

Short screws

The top cover must be installed to avoid the risk of
electric shock or short circuit.

Failure to do so can

cause serious injury, fire, electric shock or death.

WARNING

4. Make sure the leveling legs on the front-loading

washer are fully retracted before stacking it
on top of the pedestal washer.

Position the

appliance on top of the pedestal washer.

Washer legs

5. Make sure the holes on the pedestal washer

align with the

holes in the front-loading washer,

then install 4 long screws (included in box) at
each

corner to securely attach the front-loading

washer to the pedestal washer.

Long screws

6. Extend the legs of the front-loading washer

slightly until it is snugged up against the pedestal
washer.

TOOLS YOU WILL NEED

Adjustable Pliers

•

Carpenter's Level

Screwdriver

MFL68267012_E.indd 9

16. 8. 8. 오전 8:50

Summary of Contents for WD205C Series




































Search results

Summary of Contents for WD205C Series

Reviews:

Related manuals for WD205C Series

Brands by name

Popular brands

LG SIGNATURE WD205C Series, Owner'S Manual

Search results

Summary of Contents for WD205C Series

Reviews:

Related manuals for WD205C Series

Brands by name

Popular brands