background image

7

ENGLISH

Lifting and Moving the TV

When moving or lifting the TV, read the following 

to prevent the TV from being scratched or 

damaged and for safe transportation regardless of 

its type and size.

 

It is recommended to move the TV in the box or 

packing material that the TV originally came in.

 

Before moving or lifting the TV, disconnect the 

power cord and all cables.

 

When holding the TV, the screen 

should face away from you to 

avoid damage.

 

Hold the top and bottom of the TV frame firmly. 

Make sure not to hold the transparent part, 

speaker, or speaker grille area.

 

Use at least two people to move 

a large TV.

 

When transporting the TV by 

hand, hold the TV as shown in the 

following illustration.

 

When transporting the TV, do not expose the TV 

to jolts or excessive vibration.

 

When transporting the TV, keep the TV upright; 

never turn the TV on its side or tilt towards the 

left or right.

 

When handling the TV, be careful not to damage 

the protruding buttons.

 CAUTION

 

Avoid touching the screen at all times, as this 

may result in damage to the screen.

 

Do not place the product on the floor with its 

front facing down without padding. Failure to do 

so may result in damage to the screen.

 

Do not move the TV by holding the cable 

holders, as the cable holders may break, and 

injuries and damage to the TV may occur. 

(Depending upon model)

 

Make sure to attach the AV box fixing supporter 

to the AV box before you lift the product and 

move. Moving the product without attaching the 

AV box fixing supporter to the AV box first may 

cause injury to your fingers.

Summary of Contents for OLED65G6P















































Reviews: