LG-Ericsson iPECS ES-4526G User Manual Download Page 339 | Manualshive

Page: 339 / 1328

background image

C

HAPTER

14

| Security Measures

Configuring 802.1X Port Authentication

– 339 –

ES-4500G Series

Figure 186: Configuring Port Security

The operation of 802.1X on the switch requires the following:

◆

The switch must have an IP address assigned.

◆

RADIUS authentication must be enabled on the switch and the IP

address of the RADIUS server specified.

◆

802.1X must be enabled globally for the switch.

◆

Each switch port that will be used must be set to dot1X “Auto” mode.

◆

Each client that needs to be authenticated must have dot1X client

software installed and properly configured.

◆

The RADIUS server and 802.1X client support EAP. (The switch only

supports EAPOL in order to pass the EAP packets from the server to the

client.)

◆

The RADIUS server and client also have to support the same EAP

authentication type – MD5, PEAP, TLS, or TTLS. (Native support for

these encryption methods is provided in Windows XP, and in Windows

2000 with Service Pack 4. To support these encryption methods in

Windows 95 and 98, you can use the AEGIS dot1x client or other

comparable client software)

C

ONFIGURING

802.1X

G

LOBAL

S

ETTINGS

Use the Security > Port Authentication (Configure Global) page to
configure IEEE 802.1X port authentication. The 802.1X protocol must be

enabled globally for the switch system before port settings are active.

CLI R

EFERENCES

◆

"802.1X Port Authentication" on page 753

P

ARAMETERS

These parameters are displayed in the web interface:

◆

Port Authentication Status

– Sets the global setting for 802.1X.

(Default: Disabled)

802.1x
client

RADIUS
server

1. Client attempts to access a switch port.
2. Switch sends client an identity request.
3. Client sends back identity information.
4. Switch forwards this to authentication server.
5. Authentication server challenges client.
6. Client responds with proper credentials.
7. Authentication server approves access.
8. Switch grants client access to this port.

«
...
337
338
339
340
341
...
»

Summary of Contents for iPECS ES-4526G

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS ES-4526G

Brand: D-Link Pages: 267

Brand: H3C Pages: 1089

Brand: SIMON RWA Pages: 3

Brand: SMC Networks Pages: 102

Draco major K474-U8/C8

Brand: Ihse Pages: 167

Brand: steute Pages: 10

Brand: Edge-Core Pages: 9

PAT TRS 05 / PATB3

Brand: Hirschmann Pages: 12

Brand: Erbe Pages: 118

CT.TS005.003902

Brand: Talkswitch Pages: 309

Brand: Eaton Pages: 2

SI1P-SH-DVI-UCAC

Brand: Black Box Pages: 16

Brand: Gomax Pages: 24

iServer MicroServer EIS-2B

Brand: Omega Pages: 68

Brand: Kramer Pages: 4

Brand: Zektor Pages: 30

Brand: Clare Controls Pages: 2

LMP-2012G-SFP Series

Brand: ANTAIRA Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands