LFFH Metal Laboratory Casework Installation Manual Download Page 24 | Manualshive

Page: 24 / 35

background image

21

FLOOR CASES

Floor Case Installation

To prevent tipping, floor case units must be secured to a wall or otherwise supported vertically. After leveling

the units, install fasteners through the inside of the cabinet, near the corners if possible, into the wall. At least

three fasteners per side is recommended.

CAUTION: Install a filler block of wood in the cavity behind the floor case, where the fasteners will go into the

wall, to keep the cabinet’s back flat and free of dimples.

Removing Floor Case Sliding Doors

Please see the procedures above for removing wall case sliding doors. The procedures are the same for floor case

sliding doors.

Install fastener through

cabinet into wall

Wall

«
...
22
23
24
25
26
...
»

Summary of Contents for Metal Laboratory Casework




































Reviews:

No comments

Related manuals for Metal Laboratory Casework

Brand: Kangaroo Pages: 22

Brand: Daybreak Pages: 2

Brand: NABBI Pages: 23

Brand: Gautier Pages: 8

Brand: OLG Pages: 6

Brand: Target Pages: 10

Brand: Community Playthings Pages: 2

Morgan Office Chair

Brand: John Lewis Pages: 9

Brand: Novogratz Pages: 5

Brand: Noble House Home Furnishings Pages: 26

Brand: System Build Pages: 8

Indoor Lighting 31406-23

Brand: Triarch Pages: 2

Quadro Square 3P Run workstation

Brand: Jason.L Pages: 7

Elford 245/8911

Brand: Heart of House Pages: 7

Brand: Unfinished Furniture of Wilmington Pages: 6

Brand: Simmons Juvenile Furniture Pages: 4

Brand: JWA Pages: 9

Brand: hayneedle Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands