Lexmark X73 4402-001 Service Manual Download Page 38 | Manualshive

Page: 38 / 64

background image

4-4

Service Manual

4402-001

Operator Panel Removal

1. Remove the scanner lid.

2. Remove the rear cover.

3. Disconnect the operator panel cable from the system board.

4. Depress two latches on the left side of the operator panel.

5. Lift the operator panel and remove.

Top Housing Assembly Removal

1. Remove the scanner lid.

2. Remove the rear cover.

3. Disconnect the operator panel cable from the system board.

4. Remove the operator panel.

5. Remove two screws from the top housing.

6. Lift the right side of the housing.

7. Remove the top housing assembly.

Paper Support Removal

1. Open the paper support.

2. Depress the paper support at the hinge.

3. Remove the paper support.

«
...
36
37
38
39
40
...
»

Summary of Contents for X73 4402-001

































































Reviews:

No comments

Related manuals for X73 4402-001

IR5000 - iR B/W Laser

Brand: Canon Pages: 86

Brand: Datamax Pages: 2

870 - SuperScript B/W Laser Printer

Brand: NEC Pages: 52

SuperScript 1800

Brand: NEC Pages: 8

imageRUNNER ADVANCE C5255

Brand: Canon Pages: 64

Powershot A3100 IS

Brand: Canon Pages: 6

imagePROGRAF TC-20

Brand: Canon Pages: 44

Brand: Canon Pages: 88

Brand: Samsung Pages: 199

Brand: Pantum Pages: 164

Brand: Ricoh Pages: 682

Brand: HPRT Pages: 2

AccurioPrint 2100

Brand: Konica Minolta Pages: 32

Brand: Cashino Pages: 51

3600DN - Phaser B/W Laser Printer

Brand: Xerox Pages: 2

Brand: Oki Pages: 192

Brand: Olivetti Pages: 69

Multi-Font NX-2415

Brand: Star Micronics Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands