Diagnostic Information 2-31
No DC Power
No Pickup (Manual Feed)
FRU
Action
1
AC power
supply
Unplug the power cable. Is AC power being supplied
to this cable? Check AC power.
2
Wiring
DC load
Turn the power switch OFF, and disconnect
connectors J3, J4, and J5. Plug in the power cable,
and turn the power switch ON. Are the above
mentioned power supply unit connectors correctly
outputting DC power? Take care not to cause a
short. Turn the power switch OFF, connect 1 of the
disconnected connectors, and turn the power switch
ON. Repeat this for all the connectors, and
investigate the connector operating the protection
circuit, checking the wiring from that connector and
the DC load.
3
Fuse
Power supply
unit
Is the power supply unit fuse blown? Replace the
fuse. Replace the power supply unit.
FRU
Action
1
Gear
Is the pickup motor drive properly transmitted by the
gears? Check the gears, and replace any damaged
ones.
2
Pickup motor
Pickup PCB
Does the pickup motor rotate?
Check the connection of pickup PCB connector
J304, and if it is normal:
Replace the pickup motor.
Replace the pickup PCB.
3
Pickup PCB
Manual feed
solenoid
Turn the power switch OFF, remove the pickup unit,
and disconnect the connector J33. Measure the
resistance between cable connectors J33-1 and
J33-2. Is it about 100 Ohms? If yes, replace the
pickup PCB. If no, replace the manual feed solenoid.
Summary of Contents for Optra C
