background image

17

English

17

CD PROGRAMMED PLAY

AUX IN OPERATION

Use the program function to preselect the order in which a sequence of tracks will be played. 

Up to 20 tracks can be programmed.

1. Slide the FUNCTION selector to the CD position.

2. Press MODE, program indicator will light and  “01” will blink on the LED display.

3. Use SKIP FORWARDS or SKIP BACKWARDS to select the first track to include in the 

programmed sequence.

4. Press MODE to confirm and store the track.

5. Repeat steps 3 and 4 to program the other desired tracks.

6. Press PLAY to begin playback. The tracks will be played in the programmed order. The 

PLAY/PAUSE/PROG indicator flashes when the program function is in use.

Note:

• To cancel the program function, press the STOP button until the PLAY/PAUSE/PROG 

indicator goes off.

• During program setting, press STOP or open the CD door.

You can play music through the speakers of this Radio CD Player by connecting its AUX IN 

jack to your MP3 or other digital audio player.

1. Plug one end of an audio cable (not included) into the AUX IN jack located at the back of 

the unit, and the other end of the cable to the line out jack of the device you want to connect.

2. Slide the FUNCTION selector to the AUX position.

3. Adjust the VOLUME control to your desired listening level.

4. Use the function keys of your audio device to pause and resume the playback, adjust the 

volume and select the next or the previous track.

5. To switch off the unit, remove the plug from the AUX IN jack, then press the standby 

button.

HEADPHONE OPERATION

Turn the unit volume to minimum before connecting your headphone (not included) to the 

headphone jack. Headphones should have a 3.5mm diameter stereo plug and an impedance 

of 8 – 32 ohms. When headphones are connected, the speakers are automatically 

disconnected.

Note:

Extended listening of music at high volume may damage your hearing. It is highly 

recommended to use at comfortable volume levels.

RCD102seriesIM1084_19Feb_V10.indd   17

19/02/2014   3:14 PM

Summary of Contents for RCD102series













Reviews: