background image

 

User Manual for BFS-i06 

www.levitronix.com 

 

PL-3502-00, Rev00, DCO# 21-249 

 

18

 

 

Troubleshooting and Support 

6.1  Troubleshooting for Operation with PLC 

The integrated  PLC

 

provides status and error signals. However, the source of error cannot be  identified by 

these signals. For detailed analysis and debugging it is recommended to use the 

Levitronix

 Service Software 

(see  below)

Alternatively,  the 

Status

Error

Warning

  and 

Message

  bytes  can  be  read  using  Modbus 

commands  on  the  RS485  interface.  The  firmware  specification  document,  available  at  the 

Levitronix

®

 

Technical  Service  Department

  (see 

Section  6.3

),  contains  all  details  for  configuration  and  interpretation  of 

these commands.  
 

6.2  Troubleshooting with Service Software 

The 

Levitronix

 Service Software 

allows communication with the bearingless fan in connection with a PC and 

a RS485 to USB converter (see 

Table 2

). 

The 

Service  Software

  can  be  used  to  operate  the  system,  for  troubleshooting,  parameter  logging  and  user 

specific system configuration. For usage of the 

Service Software

 contact the 

Technical Service Department

 

(see 

Section 6.3

). 

 

6.3  Technical Support 

For  troubleshooting,  support  and  detailed  technical  information  contact 

Levitronix

 

Technical  Service 

Department

 
 

 
Levitronix

  

Technical Service Department 

Technoparkstr. 1 
CH-8005 Zurich 
Switzerland 
 
Phone for US:               888-569 07 18 
Phone for outside US:    +1 888-569 07 18 
E-Mail:                [email protected] 
 

 

Summary of Contents for BFS-i06





















Reviews: