background image

 

User Manual for BFS-i06 

www.levitronix.com 

 

PL-3502-00, Rev00, DCO# 21-249

 

 

First Release: 26-Jan-2018 

Last Update: 03-Nov-2021

 

 

 
 

Bearingless Fan BFS-i06 

 

 

915 Pa  
8.4 m

3

/min 

    (3.68 inH

2

O) 

    (297 cfm) 

Max. Speed: 13000 rpm 

 

 

 
 

USER MANUAL 

 

 

This manual contains information necessary for the safe and proper use of the 

BFS-i06 

bearingless fan. 

Included are specifications for the standard configurations and instructions regarding its use, installation, 
operation,  adjustment,  inspection  and  maintenance.  For  special  configurations  refer  to  accompanying 
information. Please familiarize yourself with the contents of this manual to ensure the safe and effective 
use of this product. After reading this manual, please store it where the personnel responsible for operating 
the bearingless fan can readily refer to it at any time.  

The 

Levitronix

®

 Service Software

 (with according manual 

Levitronix

 Doc.# 

PL-4048-00

) is available for 

operation, troubleshooting, parameter logging or user specific configurations. For the bearingless fan the 

Levitronix

®

 Service Software 

version

 V2.0.5.0 

or higher is needed

.

 

Summary of Contents for BFS-i06





















Reviews: