FCC COMPLIANCE STATEMENT:
Contains FCC ID: SZV-TCM2XXC. Contains IC: 5713A-TCM2XXC
The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (i.) this device may not cause harmful interference and (ii.) this device must accept
any interference received, including interference that may cause undesired operation.
Leviton is a registered trademark of Leviton Mfg. Co. in the United States, Canada, Mexico, and
other countries. Other trademarks herein are the property of their respective owners.
ETL (US) -
Conforms to UL STD 244A & UL 2043 Plenum rating. This device was tested according
to and was found to comply with UL 244A Solid State Controls for Appliances.
ETL (Canada) -
Certified to CAN/CSA STD C22.2 No. 14. This device was tested according to and
was found to comply with CAN/CSA STD C22.2 No. 14.
Press Transmitter
Figure B
CLR
LRN
For indoor use only.
For permanently installed fixtures only
.
WHT
RED=N.O.
BLU=N.C.
YEL=Com.
BLK
FCC ID: SZV-TCM2XXC
IC: 5713A-TCM2XXC
3155572
STD: UL 244A
This product complies with part 15 of
FCC rules
.
See product manual.
120VAC
CLR
LRN
Figure C
Clear All
WSP05-0x0
BREAKER PANEL
NOTE:
The wire colors will be different
for WSP05-080 and WSP05-020,
different voltages have different color wires.
HOT
NEUTRAL
GREEN OR BARE
WHITE
GROUND
BLACK
RE
D
N.
O.
AC
PO
W
ER
AC
PO
W
ER
W
HI
TE
BL
AC
K
GREEN OR BARE
AC POWER
WHITE
GROUND
FIXTURE
AC POWER
BLACK
BATTERY-FREE,
WIRELESS SWITCHES
WIRELESS
CONTROL
SIGNAL
UP TO
150 FT.
WSS0S-D0x
WSS0S-D2x
Figure D
Single Pole or Multi-way Wireless Switch (1 or more wireless light switches)
Automatic ON / Automatic OFF.
If the receiver learns a wireless motion sensor, the
load will turn OFF after no occupancy has been detected for 15 minutes. If learned
in the Rocker Mode, the output will be Manual ON / Automatic OFF. If learned in
Momentary Mode, the output will be Automatic ON / Automatic OFF.
ADDITIONAL PROGRAMMING OPTIONS
Inverted Output Mode:
The receiver supports the Inverted Output Mode of operation.
In the default configuration, the N.O. relay contact is open (not connected) when not
active, and closed (connected) when active. When the outputs are in Inverted Output
Mode, the N.O. contact is closed when not active and open when active. Inverting the
outputs may be used to emulate a normally closed relay that opens when a switch is
activated.
One common use for this mode is for magnetic door release controls. The output is
ON and the door-hold electromagnet is active until a Momentary switch is activated,
deactivating the electromagnet and allowing the door to close. The magnet is
reactivated as soon as the switch is released.
Inverted Output Mode Programming Instructions
1.
Turn the power to the receiver OFF.
2.
Press and hold the CLR button for 5 seconds while turning on the power. The load
will blink twice to indicate activation of Inverted Output Mode.
To change back to normal operating mode, repeat
Steps 1 and 2
. The load will blink
once to indicate normal (non-Inverted) mode. The state of this mode is stored in
non-volatile memory and is maintained even if the power is removed.
CLR
LRN
For indoor use only.
For permanently installed fixtures only
.
WHT
RED=N.O.
BLU=N.C.
YEL=Com.
BLK
FCC ID: SZV-TCM2XXC
IC: 5713A-TCM2XXC
3155572
STD: UL 244A
This product complies with part 15 of
FCC rules
.
See product manual.
120VAC
CLR
LRN
Enter Learn Mode
Figure A
For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only)
www.leviton.com
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at
the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for
five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement,
at its option, if within such five year period the product is returned prepaid, with proof of purchase date, and a
description of the problem to
Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201
North Service Road, Melville, New York 11747.
This warranty excludes and there is disclaimed liability for
labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or
in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used
under normal operating conditions or not in accordance with any labels or instructions.
There are no other or
implied warranties of any kind, including merchantability and fitness for a particular purpose
, but if any
implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including
merchantability and fitness for a particular purpose, is limited to five years.
Leviton is not liable for incidental,
indirect, special, or consequential damages, including without limitation, damage to, or loss of use of,
any equipment, lost sales or profits or delay or failure to perform this warranty obligation
. The remedies
provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
© 2010 Leviton Mfg Co., Inc.
DI-000-WST05-00A
SPECIFICATIONS
WSP05-010
WST05-010
WSP05-080
WST05-080
WSP05-020
WST05-020
Range
50-150 feet (typical)
Frequency
315 MHz (868MHz for International)
Relay Output
120 VAC
240 VAC
277 VAC
Max
Loads/
Contact
Ratings
Tungsten / Incandescent
500 W
1000 W
1150 W
Fluorescent Ballast
3 A
General Duty
6 A
A300 Pilot Duty
120 VA
240 VA
277 VA
Power Supply
120 VAC
50/60 Hz
240 VAC
50/60 Hz
277 VAC
50/60 Hz
Output Channels
1 FORM A Relay
Memory
Stores up to 30 switch IDs
Dimensions
2.11 x 1.73 x 1.09 inches (54 x 44 x 28 mm)
2.61 x 1.73 x 1.09 inches (66 x 44 x 28 mm)
Threaded mount version
Operating Temperature
14° to +122°F (-10° to +50°C)
Storage Temperature
-4° to +176°F (-20° to +80°C)
Radio Certification
FCC (United States): SZV-TCM2XXC
I.C. (Canada): 5713A-TCM2XXC
Safety Approval
ETL (U.S.): UL244A & UL 2043 Plenum rating
ETL (Canada): CSAc22.2#14-05
UL 2043 Plenum rating
Note:
Electrical Specifications apply to threaded mount and international versions.
Figure E
Wireless Relay mounting options
Outside junction box
Junction box
Threaded
Wireless
Relay
Inside junction box
Junction box
Wireless
Relay