For Technical Assistance Call: 800-824-3005 - www.leviton.com
© 2013 Leviton Mfg. Co., Inc.
FOR CANADA ONLY
For warranty information and/or product returns,
residents of Canada should contact Leviton in writing
at
Leviton Manufacturing of Canada Ltd to the
attention of the Quality Assurance Department, 165
Hymus Blvd, Pointe-Claire (Quebec), Canada H9R
1E9
or by telephone at
1 800 405-5320.
Table 1 - Leviton UPB™ 15A Relay Switch Local Operation
Rocker Event
Top Rocker
Bottom Rocker
Single-Tap
Load turns on.
Load turns off.
Leviton AUXILIARY SWITCH OPERATION
The Leviton UPB™ Wall Switch can be connected to
one or more Leviton Auxiliary Switches producing multi-
way circuits. Each Leviton Auxiliary Switch has a rocker
switch that controls the load in the exact same manner
as the rocker switch on the connected Leviton UPB™
Wall Switch, as previously described. When connected,
the LED remains continually on at all times while power
is applied.
LED Indicator
The Leviton UPB™ Wall Switch comes equipped with
a multi-color LED indicator that is normally lit to blue
when the load is off. The LED is off when the load is
on.
If used, the LED in the Leviton Auxiliary Switch is
always lit.
Setup Mode
To configure the Leviton UPB™ Wall Switch using an
Leviton controller or a PC running the UPB™ UPStart
configuration software, it must be put into Setup Mode
as follows:
Step
Operation
1
Tap the rocker switch quickly 5 times.
2
The Leviton UPB™ Wall Switch will cycle the load one time and blink its LED blue to indicate that it is in
Setup Mode.
NOTE:
the switch will automatically exit Setup mode after 5 minutes.
Figure 4 - Wiring Diagram
LINE
NEUTRAL
37A00 (OPTIONAL)
AUXILIARY SWITCH
AUXILIARY SWITCH
37A00 (OPTIONAL)
40A00
HAI Relay Switch
BLACK
BLACK
BLACK
RED
WHITE
YELLOW
YELLOW
*BLUE AND/OR GRAY
*BLUE AND/OR GRAY
YELLOW
*CONNECTING THE BLUE AND/OR GRAY WIRE TO NEUTRAL SETS THE COLOR OF THE LED INDICATOR.
CONNECT BLUE FOR BLUE INDICATOR, GRAY FOR RED INDICATOR, OR BOTH FOR MAGENTA INDICATOR.
BLUE AND/OR GRAY WIRE MAY BE CONNECTED TO NEUTRAL OR EARTH GROUND. NEUTRAL IS RECOMMENDED.
GREEN
Line 120VAC, 60Hz
NOTE:
It is normal for this switch to make a slight
buzzing sound during operation. It is also normal for
the switch and wall plate to feel warm to the touch.
SPECIFICATIONS
Reset to Factory Default Settings
To reset the Leviton UPB™ Wall Switch to factory default settings:
Model Number
40A00-1
Incandescent Loads, Inductive Loads, and Florescent Loads
Yes
Motor-Operated Appliances
Yes
Current Maximum
15A
Connections
18 GA
LED Indicator
Yes
Dimensions
4.1 x 1.75 x 1.45
Weight
0.25 lb.
Mounting
Standard J Box
Input Power
120 ± 12 VAC
Input Frequency
60 ± 3 Hz
Operating Temperature
-40 °F to 104 °F
Step
Operation
1
On the Leviton UPB™ Wall Switch that you want to reset to factory default, tap the rocker switch
quickly 5 times.
2
The Leviton UPB™ Wall Switch will cycle the load one time and blink its LED blue to indicate that it
is ready to be reset.
3
Tap the rocker switch quickly 10 times to reset to factory default setting.
4
The Leviton UPB™ Wall Switch will cycle the load one time and blink its LED red to indicate that it
has been reset.
5
Tap the rocker switch once more to stop the LED from blinking.
DI-022-HL401-05A
AR2253
FCC Compliance
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
LEVITON LIMITED WARRANTY
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that products manufactured by Leviton under the Leviton brand name (“Product”) will be free from defects
in material and workmanship for the time periods indicated below, whichever is shorter:
• OmniPro II and Lumina Pro: three (3) years from installation or 42 months from manufacture date.
• OmniLT, Omni IIe, and Lumina: two (2) years from installation or 30 months from manufacture date. • Thermostats, Accessories: two (2) years from installation or 30 months from manufacture date.
• Batteries: Rechargeable batteries in products are warranted for ninety (90) days from date of purchase.
Note:
Primary (non-rechargeable) batteries shipped in products are not warranted.
Products with Windows
®
Operating Systems:
During the warranty period, Leviton will restore corrupted operating systems to factory default at no charge, provided that the product has been used as
originally intended. Installation of non-Leviton software or modification of the operating system voids this warranty. Leviton’s obligation under this Limited Warranty is limited to the repair or replacement,
at Leviton’s option, of Product that fails due to defect in material or workmanship. Leviton reserves the right to replace product under this Limited Warranty with new or remanufactured product.
Leviton will not be responsible for labor costs of removal or reinstallation of Product
. The repaired or replaced product is then warranted under the terms of this Limited Warranty for the remainder of
the Limited Warranty time period or ninety (90) days, whichever is longer. This Limited Warranty does not cover PC-based software products.
Leviton is not responsible for conditions or applications
beyond Leviton’s control
.
Leviton is not responsible for issues related to improper installation, including failure to follow written Installation and operation instructions, normal wear and
tear, catastrophe, fault or negligence of the user or other problems external to the Product
. To view complete warranty and instructions for returning product, please visit us at
www.leviton.com
.
Use herein of third party trademarks, service marks,
trade names, brand names and/or product names
are for informational purposes only, are/may be the
trademarks of their respective owners; such use is not
meant to imply affiliation, sponsorship, or endorsement.
WEB
VERSION
