manualshive.com logo in svg

LevelOne HVE-6601R, User Manual

Share
Download
LevelOne HVE-6601R User Manual Download Page 16

Installation Procedure (3x3) Using 
Web UI: 

1. Prepare host(HVE-6601T) x 3 and client x 9(HVE-6601R). 
2. Follow Figure 1 to construct the whole system. 
3. Reboot all devices. Ensure that all remote displays and all network cables are 

connected correctly. (Video source is required at this step) 

4. If the control PC (Windows OS) doe

sn’t install bonjour SDK yet, please install it. 

Google 

“bonjour SDK download” for the installation file or download it here: 

http://developer.apple.com/opensource/

 .

 

5. Configure the control 

PC’s network setting to use 169.254.xxx.xxx IP domain 

with netmask 255.255.0.0. Or immediate running LinkTool.exe (copy from 
CD of package to control PC). 

6. Open 

PC’s web browser (Google Chrome performs best. IE is not recommended). 

Link to the control portal (the first HVE-6601) by following web address 
http://last-gateway0000.local/vw/ . 

 

The 0000 part in above web address is mapping to the value of 4bits 
DIP switch. 

7. If link success, user will see the web page as following :   

       
 

 

 

Summary of Contents for HVE-6601R































Reviews:

No comments

Brands by name

Popular brands

Load more brands